• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.
  • The forums have been upgraded with support for dark mode. By default it will follow the setting on your system/browser. You may override it by scrolling to the end of the page and clicking the gears icon.

USB Hub conversion, now it's useful.

Necrofire

New Member
Joined
Nov 1, 2007
Messages
585 (0.09/day)
System Name Chuck
Processor Core i5-2500k @ 4.5Ghz
Motherboard msi P67A-C43
Cooling hyper 212, 2 120mm fans
Memory 8GB DDR3 1600MHz
Video Card(s) XFX 6870
Storage 60GB sata3 sandforce ssd, 1TB samsung hdd
Display(s) Yamakazi Catleap
Case Possibly Antec, not sure
Audio Device(s) Onboard
Power Supply Rosewill 600W
Conversion of a 4-port USB hub to house 2GB flash drive and a micro-SD card reader.

I started this project because having to carry my micro-sd card reader, my 2GB flash drive, a USB hub, and a very long usb cord was difficult, since my laptop bag is small and filled with crap as it was. My goal was to have the card reader and flash drive neatly tucked away inside the casing for the hub. The hub had a lot of extra space, so this wasn't a problem.

Details below...

Parts list, in picture form. Btw, these are thumbnails, click them to get full pic.:toast:
Pic Pic
Missing from the list is my multimeter. Also, I didn't purchase anything for this project, this just details how much the things I used on this project cost.

Here's everything in tact, minus the casing.
The Vakoss USB hub was $10 from Frys Electronics, the Datel Micro-SD card reader came with the Datel Games N Music for DS for $12 off ebay, and my Emprex 2GB Flash drive. was $11 on sale at Frys Electronics.
Pic Pic

Starting out, I tried unsoldering the usb plugs off of the devices and hub. Lead-free solder sucks, so I was forced to pry off the plugs on everything with some trusty pliers.
Small note, I only had to pry off the, umm, "support beams" for the plug, the power and data leads came off fine with solder. For the hub's pins, I pulled the plug off, and instead of unsoldering the pins off, I simply cut them short, allowing me to solder wires to them.
Pics

After everything was off, I took a cut-up USB wire, and grabbed about 3 or so inches of the 4 wires inside.
I noted which pin on the devices was pin 1 (red) and proceeded to first solder (red)(white)(green)(black) wires onto the hub for the card reader.
Eying it, I could see that the 12MHz crystal oscillator on the card reader would be too tall for the hub's casing. I ended up carefully bending the oscillator to the side, and out of the way.
Also, I had to slightly move a capacitor on the hub to make some room for said oscillator.
Pic

After finishing up some soldering and some heatshrink wrapping, I tested for shorts with my multimeter and then tested my work by plugging it in. Success.:roll:
Pic

Now, hot glue isn't necessary, but I put it there so my crappy soldering and wrong-sized heatshrink wouldn't come undone.
Pic
EDIT: Forgot to resize this sucker. Eh, don't feel like it.

After wiring up the second port to accommodate my flash drive, I was curious to see if the hub's controller became hot like any other processor. I was only concerned because my flash drive is cheaply built, and one of the memory chips on it would be directly touching said usb hub controller.
Instead of toughing it out and hoping it wouldn't matter, I decided to just put a make-shift heatsink in between the two chips.
Pic
Note: Thanks go to ASRock for supplying this beautiful MCP61P Northbridge heatsink for this project. (I have to say, the heatsink did NOT do a good-enough job cooling my northbridge, so I replaced it with a larger heatsink, and put a fan on said larger heatsink:rockout:)

Now, this step was also unnecessary, but I had some AS5 laying around so I did it.
Pic

And here's the heatsink. Right now it's held on by the AS5, but later it fell off, and so I ended up hot-gluing the heatsink on. (NOT in between heatsink and chip, that would be silly:p)
Pic

Boring and unimportant story ahead! You can skip to next paragraph if you hate reading:toast:
I was almost done, I just needed to solder 4 more wires to my flash drive. While soldering the last wire, one of the wires came off the hub. I though "no big deal" and attempted to solder it back on. Well, as I started to solder it, a wire can undone on the flash drive end. Again, no big deal, I just didn't wet those wires well enough before hand.
Well, after that was soldered, everything was in place and I hurriedly hot-glued the wires. DONE! Well, that's waht I thought. There was too much wire and hot glue, and I couldn't fit the the flash drive with everything else in the casing.
I ended up getting kinda frustrated:banghead: (because it was 3am and I wanted to be done) so I pulled hard on the flash drive, ripped all 4 wires off, and went to sleep:shadedshu.

Resuming the project, I decided on using IDE cable wire for the flash drive. I have ~20 or so IDE cables (40- and 80-pin, as well as some floppy) so tearing up one didn't bother me.
Pic
Note, it was A LOT EASIER to strip the cable, solder it, and make it look pretty, as well as get it out of the way. I absolutely recommend this wire for this type of job if you suck at soldering and lack a wire-stripper.

Done! Time for a quick test.
Pic
Note how the heatsink is hot-glued on.

And there we go, everything is perfect.
Pic
Pic

And here it is, plugged in and working.
Pic
I have to mention that the hub can easily take 4 devices without external power, since most devices don't need >100mA from USB for power. My phone works fine for accessing the card, the power is plugged into the hub just so that I could confirm that it would charge.:D

Pic
 
Last edited:
Very nice and impressive
 
Thanks, I'm wondering if this is possible with other hubs. My hub was cheap, and there was a lot of space being wasted inside the hub.
 
Very nice, looks like something I would do if i was bored enough. :P
 
Bloody hell. Nice mod dude. Make's me wonder...
 
Makes you wonder how easy it really is to put something inside something else?
 
Well, it depends on how large the casing for it is.
I managed to fit a full atx mobo and 3 hard drives into a mini tower. There's a lot of room that's wasted in a lot of cases.
 
Update: I was charging my phone for a while, and after about half an hour I decided to check if the hub was warm or not. Well, the thing was abnormally warm. I'm not sure if my flash drive will take the heat for long.
 
Update: I was charging my phone for a while, and after about half an hour I decided to check if the hub was warm or not. Well, the thing was abnormally warm. I'm not sure if my flash drive will take the heat for long.

Cut a hole in the top and add a small exhaust fan. Nice mod, I think, can't see any pics??

:toast:
 
You can't see any pics?
 
Back
Top