- Joined
- Dec 6, 2011
- Messages
- 4,784 (1.03/day)
- Location
- Still on the East Side
EK Water Blocks, Ljubljana-based premium liquid cooling gear manufacturer, is proud to introduce a new Full Cover water block for AMD flagship dual-processor graphics card Radeon R9 295X2, the only true single-slot liquid cooling solution on the market.
Unlike factory provided closed-loop cooling solution, the EK-FC R9-295X2 is a complex design water block. It directly cools the GPU, RAM as well as VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it's VRM to remain stable under high overclocks. EK-FC R9-295X2 water block also features a very high flow design therefore it can be easily used in liquid cooling systems using weaker water pumps.
Base is made of electrolytic copper (nickel-plated or bare - depending on the variant) while the top is made of quality cast acrylic material or POM Acetal (depending on the variant). Screw-in brass standoffs are pre-installed and allow for safe installation procedure. The cooling engine uses refined 0.7 mm wide microchannel structure to even further improve the heat transfer while not sacrificing the famous low hydraulic restriction design.
EK also encloses a single-slot I/O bracket which replaces the original two-slot in order to make installation of multiple graphics cards easier. This makes the EK-FC R9-295X2 the only true single-slot liquid cooling solution on the market. Made in Slovenia - Europe!
Up to four EK-FC R9-295X2 series water blocks can be interconnected with EK-FC Terminal which allows for hassle-free piping job.
The product is readily available for purchase through EK Webshop and Partner Reseller Network and comes in four different variants. An aesthetic retention backplate is also available:
View at TechPowerUp Main Site
Unlike factory provided closed-loop cooling solution, the EK-FC R9-295X2 is a complex design water block. It directly cools the GPU, RAM as well as VRM (voltage regulation module) as water flows directly over these critical areas thus allowing the graphics card and it's VRM to remain stable under high overclocks. EK-FC R9-295X2 water block also features a very high flow design therefore it can be easily used in liquid cooling systems using weaker water pumps.
![](https://www.techpowerup.com/img/14-05-29/EK-FC-R9-295X2_CP_full_1200_thm.jpg)
![](https://www.techpowerup.com/img/14-05-29/EK-FC-R9-295X2_NA_full_1200_thm.jpg)
![](https://www.techpowerup.com/img/14-05-29/EK-FC-R9-295X2_NP_full1_1200_thm.jpg)
Base is made of electrolytic copper (nickel-plated or bare - depending on the variant) while the top is made of quality cast acrylic material or POM Acetal (depending on the variant). Screw-in brass standoffs are pre-installed and allow for safe installation procedure. The cooling engine uses refined 0.7 mm wide microchannel structure to even further improve the heat transfer while not sacrificing the famous low hydraulic restriction design.
EK also encloses a single-slot I/O bracket which replaces the original two-slot in order to make installation of multiple graphics cards easier. This makes the EK-FC R9-295X2 the only true single-slot liquid cooling solution on the market. Made in Slovenia - Europe!
Up to four EK-FC R9-295X2 series water blocks can be interconnected with EK-FC Terminal which allows for hassle-free piping job.
The product is readily available for purchase through EK Webshop and Partner Reseller Network and comes in four different variants. An aesthetic retention backplate is also available:
![](https://www.techpowerup.com/img/14-05-29/EK-FC_R9-295X2_lineup_thm.jpg)
View at TechPowerUp Main Site