Antec C8

[Darksaber]

The Antec C8 represents the largest of the Constellation series dual-chamber enclosures. The C8 manages to impress with a down-to-earth design, focus on functionality, and plenty of details that make the build process and final result very positive.

Show full review

 

[Bayfront Benny]

I just have one question - does this case support the new back (reverse connector) connect motherboards? I believe the C5 does but not clear if this one does too. TIA

 

[Chaitanya]

It feels good to see Antec back making good cases.

I just have one question - does this case support the new back (reverse connector) connect motherboards? I believe the C5 does but not clear if this one does too. TIA

Current C8 doesnt support those(thankfully given the placement of PSU atleast top connectors will be blocked. Wont be surprised to find a revision of this case few months down the line with support for reverse connectors.

 

[wheresmycar]

thanks for the review.

So another box on the block. I've done so much online-window-shopping over the years for one of these over-sized shoe boxes with 2 chambers, one for each shoe - now I've lost interest. Can't knock it though, some completed builds in these type of cases still look fantastic.

"In terms of build quality, Antec really did do everything right for the most part.................the overall design manages to be simple yet extremely functional"

Good job Antec!!

 

[Minus Infinity]

Wow, so surprised air doesn't turn through 90 degree bends very well. Results speak for themselves, very ordinary thermals thanks to the idiotic aquarium design.

 

[lepudruk]

Lol, so basicly it's a duplicate of Lian Li Dynamic EVO (well, without one feature - the upside down rotation). Even the accessories fit perfectly - like LL's GPU raiser.
I don't know if it was already mentioned but you can place 2x 160mm fans on bottom and top of this case - LL's 216 fans should fit easily.

Now I started to wonder if this type of case would notice any gain from switching rear fan from exhaust to intake?
Best case scenario (lowest temps and noise) is: 3x bottom intake, 3x top exhaust and back side AIO intake.
What about the rear fan? Wouldn't VRM section benefit from cool air blowing on it? I have to check it on my Evo..

 

[Ruru]

Been a while since Antec has put out something good. I may consider this as been thinking of case change.

Lol, so basicly it's a duplicate of Lian Li Dynamic EVO. Even the accessories fit perfectly (I don't know if it was already mentioned but you can place 2x 160mm fans on bottom and top of this case - LL's 216 fans should fit easily).

Personally I don't mind, IMO majority of cases are more or less copies of each other anyway.

 

[lepudruk]

Personally I don't mind, IMO majority of cases are more or less copies of each other anyway.

After I checked pricing I don't mind it either (it's a 90$ difference)

 

[Ruru]

After I checked pricing I don't mind it either (it's a 90$ difference)

View attachment 356329

Whoa, since when the O11 pricing has skyrocketed

 

[lepudruk]

Whoa, since when the O11 pricing has skyrocketed

My bad, I compared non-argb Antec with argb LL (also that was a canadian pricing, now it's US):

 

[Ruru]

My bad, I compared non-argb Antec with argb LL (also that was a canadian pricing, now it's US):

View attachment 356330

~30EUR difference here. Still that Antec looks that it's a good clone though.

 

[SN2716057]

I'm looking for an airfryer for my parents, and this will do just fine.

 

[Chomiq]

After I checked pricing I don't mind it either (it's a 90$ difference)

View attachment 356329

Well that's main problem for Antec right now, their distribution kinda sucks which leads to inflated prices. There's a direct store:

C8 White

SPECIFICATIONS main spec Dimensions 464 x 303 x 476mm (DWH) Form Factor Full Tower Materials Steel + Plastic + Glass Mainboard Support E-ATX (280mm), ATX, M-ATX, ITX Front Access & Controls Power, Reset, USB 3.0 x 2, Type-C 10Gbps x 1, Headphone/Mic Combo Jack Side Panel 4mm Tempered Glass Drive...

antecplay.com

which has some of the recently announced models listed (aluminum and wooden front options) but it looks like availability depends on currency used.

Anyway, this "clone" has better fan support than the original 011D and its built quality is on par. If I were to switch to this type of case it would be one of the three possible picks, along O11D Evo and that new BeQuiet case.

I'm looking for an airfryer for my parents, and this will do just fine.

Base model has no included fans, what did you expect from a test that does not include any standardized fans?

 

[Caring1]

Wow, so surprised air doesn't turn through 90 degree bends very well. Results speak for themselves, very ordinary thermals thanks to the idiotic aquarium design.

I think that is more a reflection of the fact fans weren't placed on the bottom of the case to have bottom to top airflow. Side fans are a stupid idea IMO.

I believe the PSU placement should be a big negative for this case as it makes it harder to change the CPU cooler and inhibits airflow over the back of the Motherboard's CPU region.
I had this case short listed until that factor was known.

 

[dj-electric]

Statements like "Antec is back" and "It has been a while since Antec did X or Y" are a little strange to those of us who have been working tightly with Antec products for many many years now and without pause. Antec release new products on a quarterly basis. That said, most of them are based on similar designs and are of low-cost nature

Seems to be mostly a North American thing, since they have been gone from that market for a while.

I would love to see Antec's PSUs that aren't their signature series getting reviews. I know their new NeoEco ATX 3.0 series of power supplies are selling well where Antec is present.