I need help getting 205x21 from not BSOD. I get;
"IRQL_NOT_LESS_THAN_OR_EQUAL"
0x0A
I've had some other codes but can't remember them. It doesn't seem to matter how much vcore is applied as it doesn't help. I'm backed down the uncore and ram to their lowest multi to try and isolate it. I'm at 1.425 vcore and only seeing ~82C on the hottest core.
This is LinX/IBT stable settings for 4.2Ghz. Any recommendations for 4.3?
Code:
AI Tweaker
****************************
AI Overclock Tuner: Manual
CPU Ratio Setting: 21
BCLK Frequency: 200
PCIE Frequency: 100
DRAM Frequency: DDR3-1200Mhz
UCLK Frequency: 3200Mhz
QPI Link Data Rate: 3600Mhz
*******************
DRAM Timing Control
*******************
DRAM CAS Latency: 5 DRAM Clock
DRAM RAS# to CAS# Delay : 6 DRAM Clock
DRAM RAS# PRE Time: 5 DRAM Clock
DRAM RAS# ACT Time: 15 DRAM Clock
DRAM RAS# to RAS# Delay: AUTO
DRAM REF Cycle Time: 60 DRAM Clock
DRAM WRITE Recovery Time: AUTO
DRAM READ to PRE Time: AUTO
DRAM FOUR ACT WIN Time: AUTO
DRAM Back-To-Back CAS# Delay: AUTO
DRAM Timing Mode: AUTO
DRAM Round Trip Latency on CHA: AUTO
DRAM Round Trip Latency on CHB: AUTO
DRAM Round Trip Latency on CHC: AUTO
DRAM WRITE To READ Delay(DD): AUTO
DRAM WRITE To READ Delay(DR): AUTO
DRAM WRITE To READ Delay(SR): AUTO
DRAM READ To WRITE Delay (DD): AUTO
DRAM READ To WRITE Delay (DR): AUTO
DRAM READ To WRITE Delay (SR): AUTO
DRAM READ To READ Delay(DD): AUTO
DRAM READ To READ Delay(DR): AUTO
DRAM READ To READ Delay(SR): AUTO
DRAM WRITE To WRITE Delay(DD): AUTO
DRAM WRITE To WRITE Delay(DR): AUTO
DRAM WRITE To WRITE Delay(SR): AUTO
****************************
CPU Voltage: 1.3875
CPU PLL Voltage: 1.80
QPI/DRAM Core Voltage: 1.3375
IOH Voltage: 1.20
IOH PCIE Voltage: 1.50
ICH Voltage: 1.10
ICH PCIE Voltage: 1.50
DRAM Bus Voltage: 1.60
DRAM DATA REF Voltage on CHA: AUTO
DRAM CTRL REF Voltage on CHA: AUTO
DRAM DATA REF Voltage on CHB: AUTO
DRAM CTRL REF Voltage on CHB: AUTO
DRAM DATA REF Voltage on CHC: AUTO
DRAM CTRL REF Voltage on CHC: AUTO
****************************
Load-Line Calibration: Disabled
CPU Differential Amplitude: AUTO
CPU Clock Skew: AUTO
CPU Spread Spectrum: Disabled
IOH Clock Skew: AUTO
PCIE Spread Spectrum: Disabled
CPU Advance Settings
C1E Support: Disabled
Hardware Prefetcher: Enabled
Adjacent Cache Line Prefetcher: Enabled
Intel (R) Virtualization Tech: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
Intel (R) HT Technology: Enabled
Active Processor Cores: ALL
A20M: Disabled
Intel (R) C-State Tech: Disabled
****************************
Express Gate: Disabled
I would bump the ICH just a bit. however I think the main problem is your RAM timings so tight.
DRAM CAS Latency: 5 DRAM Clock
DRAM RAS# to CAS# Delay : 6 DRAM Clock
DRAM RAS# PRE Time: 5 DRAM Clock
DRAM RAS# ACT Time: 15 DRAM Clock
DRAM RAS# to RAS# Delay: AUTO
DRAM REF Cycle Time: 60 DRAM Clock
DRAM WRITE Recovery Time: AUTO
DRAM READ to PRE Time: AUTO
DRAM FOUR ACT WIN Time: AUTO
DRAM Back-To-Back CAS# Delay: AUTO
If not then, 
