AGESA 1.2.0.8

[izy]

Can anyone check CO values on Combo V2 PI 1.2.0.B? I've noticed that my CO value of -8 isn't the same as the -8 of the previous AGESA version. Guess that's to be expected, but now I need closer to -14 to get the same voltage.

'tis on a 5700X.

Something changed for me too , my best cores that were - 23 now are working only with -22 for some reason ( i havent checked other cores but they seem stable at -27 as before) and my RAM now works procODT 32 before wasnt stable with less than 48.

 

[Makaveli]

I've not noticed any difference in CO values however my 5800X3D chip is from a 2023 batch so does -30 on all cores without issue so no changes on my end.

 

[izy]

I've not noticed any difference in CO values however my 5800X3D chip is from a 2023 batch so does -30 on all cores without issue so no changes on my end.

X3D clocks lower so prob thats why can do -30 all cores.

 

[Kodehawa]

I've not noticed any difference in CO values however my 5800X3D chip is from a 2023 batch so does -30 on all cores without issue so no changes on my end.

I'm getting higher voltage with the same CO, so it'd be a matter of comparing that rather than just how much you can push it. Technically, I can push mines higher (-14 instead of -8), but the voltage readout is the same between -8 on previous AGESA and -13 on current.

Even at -13 I'm still seeing cores going 1.41V, which was unheard even at -8. Multi-core voltage seems about the same at -13 as it was at -8, ~1.288V

 

[Makaveli]

X3D clocks lower so prob thats why can do -30 all cores.

No that isn't the reason.

The first few batches of X3D chips all couldn't do -30.

They are binned higher than the standard chips and from what i've seen most batches from this year can all do -30

I'm getting higher voltage with the same CO, so it'd be a matter of comparing that rather than just how much you can push it. Technically, I can push mines higher (-14 instead of -8), but the voltage readout is the same between -8 on previous AGESA and -13 on current.

Even at -13 I'm still seeing cores going 1.41V, which was unheard even at -8. Multi-core voltage seems about the same at -13 as it was at -8, ~1.288V

Will have to wait and see if anyone else on standard Zen 3 chips also notice a difference in CO. Most of the other forums i've been on haven't seen any post so far or reddit but will keep an eye out.

 

[Kodehawa]

Will have to wait and see if anyone else on standard Zen 3 chips also notice a difference in CO. Most of the other forums i've been on haven't seen any post so far or reddit but will keep an eye out.

Another option is that the BIOS update messed a bit with LLC. But gotta see I guess, it's kind of a moot point for me, as my CPU doesn't undervolt well, so just had to adjust CO to a point where it was at a similar voltage as before.

 

[izy]

Even at -13 I'm still seeing cores going 1.41V, which was unheard even at -8. Multi-core voltage seems about the same at -13 as it was at -8, ~1.288V

Mine goes to 1.419v too and i have 2 cores at -22 and the rest at -27, autoOC +200.

 

[GerKNG]

i just installed 1.2.0.B on two B550 Aorus Elite and now i have the same constant USB Dropouts just like it's 2020 all over again.

 

[Dragokar]

i just installed 1.2.0.B on two B550 Aorus Elite and now i have the same constant USB Dropouts just like it's 2020 all over again.

Report it to AMD and Gigabyte please, especially because it is still a beta at Gigabyte.

 

[Kodehawa]

i just installed 1.2.0.B on two B550 Aorus Elite and now i have the same constant USB Dropouts just like it's 2020 all over again.

All fine here with USB.

 

[jesdals]

i just installed 1.2.0.B on two B550 Aorus Elite and now i have the same constant USB Dropouts just like it's 2020 all over again.

I have no problems on x570 but have these settings in bios - do not know if it will help you though

But you could give it a try

 

[GerKNG]

Report it to AMD and Gigabyte please, especially because it is still a beta at Gigabyte.

already reported it to gigabyte.

I have no problems on x570 but have these settings in bios - do not know if it will help you though
But you could give it a try

sadly not working.


i was able to flash it back to 1.2.0.A which is still had on a USB Stick. works fine again as it has for the last couple years. seems to be related to 1.2.0.B on both boards in my case.

 

[Dragokar]

already reported it to gigabyte.


sadly not working.


i was able to flash it back to 1.2.0.A which is still had on a USB Stick. works fine again as it has for the last couple years. seems to be related to 1.2.0.B on both boards in my case.

Any reply from Gigabyte?

 

[AndrewRUS]

Good time to everyone!
I have a motherboard X470 GAMING PRO MAX with firmware 7B79vMF 2023-05-05 (AGESA ComboAm4v2PI 1.2.0.A) I observe problems with copying files from my computer to a flash drive-Very low speed 1-2mb Tried flash drives from different manufacturers, and reinstalled the system, the result is the same. Does it make sense to reset to AGESA ComboAm4v2PI 1.2.0.B And can anyone tell me what settings can be changed where? Thank you all in advance! Sincerely, Andrey.

 

[GerKNG]

Any reply from Gigabyte?

so far not.

 

[jesdals]

so far not.

You might be able to find inspiration til settings in bios from this thread thus its x570 its Gigabyte based and very similar https://www.techpowerup.com/forums/threads/aorus-x570-master.257392/page-20