Project: Honeycomb

Fuganater · Nov 23, 2011

New Mod City Showdown Competition Final Pics

These are crappy looking because the case is soo shiny.

Lights on!!

And finally, me and the wife!

More work to come soon!

de.das.dude · Nov 23, 2011

simply love the orange panel lighting! :rockout:

awesome build!

Fuganater · Nov 23, 2011

LEDs and Cable Managment

I started wiring up the waterblocks with LEDs.

GPU Block

Cable management time! I'm using P clips from MDPC-X which are working rather well. I also finished up the pluming.

Back fan cables

Front fan cables

Left side of HDD cavity where most of the pluming comes through the center of the case

Another shot of the right side of the HDD cavity

Bottom of the case

Some cable management on the mobo side

T-fitting on top of the mobo loop res. This attaches to the fill port on top of the case

And here is the drain port for the HDD loop res. Luckily I was able to use fittings and no tubing which made the installation super easy.

I'm doing lots more work this week.

Cheers till later!

de.das.dude · Nov 23, 2011

in the competition pics, i dont think yo put LEDs in the water block did you?

Fuganater · Nov 24, 2011

de.das.dude said:
in the competition pics, i dont think yo put LEDs in the water block did you?

No not yet. But you'll see in my next update.

Fuganater · Nov 24, 2011

LEDs, Pumps and Cables

I finished the LEDs for the CPU and RAM blocks.

I'll clean up the cables a bit later.

And so far it all looks pretty good.

All that is left for LEDs is the ones that go in the bottom of the reservoirs.

I finally finished and installed my custom ATX power cable. It still needs some work because it is bunched up. But that will come later.

And here is what it looks like connected to the PSU

A very tricky task was to mount the pumps. Since I have no hand room inside the case at the bottom, I had to remove the entire bottom panel, mount the pumps, then put it back on. Here is the final result. (A bit hard to see...)

I started sleeving the temp sensors. There are a lot of them!

And finally, I had Will make a fan buss for me. The only problem with it is that I had to extend the power connector because where it is at is an extremely tight space and I can't get my fingers back there to connect it.

Cheers till next time.

de.das.dude · Nov 24, 2011

but

sleeving would look a lot better if you can cut the heatshrink bits to equal size.

PopcornMachine · Nov 24, 2011

Fuganater said:
Cheers till next time.

Thanks so much for all the great pictures.

Congrats on quite an achievement!

Fuganater · Nov 28, 2011

de.das.dude said:
but

http://i11.photobucket.com/albums/a190/Fuganater987/Project Honeycomb/DSC09314.jpg

sleeving would look a lot better if you can cut the heatshrink bits to equal size.

Those connectors will be covered up by the PSU shround so I used mostly odds and ends for those ones. The connectors you can see are all 15mm.

PopcornMachine said:
Thanks so much for all the great pictures.

Congrats on quite an achievement!

Thanks! First round of eliminations are today!

de.das.dude · Nov 28, 2011

ahh i see what you did tehre >.>

Fuganater · Nov 28, 2011

SATA Power Cables

I started making my SATA power cables.

First, I installed all the drives. Put the SATA connectors on them. And started running the cables.

First section done.

More done.

I had to move a drive down so I could measure the last section correctly.

And the final product with the sleeved SATA Data cables installed and zipped.

I'm happy with how they came out. I did the same thing for the other HDD cage but I ran out of heat shrink

so I put another order in for it at MDPC-X. My ATX pin remover is also starting to go... I think I need to spend the money and get the good one.

Cheers till next time!

de.das.dude · Nov 29, 2011

atx pins are easy to remove even with tweezers. molex ones are a bitch

Sinzia · Nov 29, 2011

The only thing that doesn't look amazing is the heatshrink... they're all different lengths.

Peter1986C · Nov 29, 2011

Fuganater said:
I started making my SATA power cables.

First, I installed all the drives. Put the SATA connectors on them. And started running the cables.

First section done.
http://i11.photobucket.com/albums/a190/Fuganater987/Project Honeycomb/DSC09413.jpg

More done.
http://i11.photobucket.com/albums/a190/Fuganater987/Project Honeycomb/DSC09416.jpg

I had to move a drive down so I could measure the last section correctly.
http://i11.photobucket.com/albums/a190/Fuganater987/Project Honeycomb/DSC09419.jpg

And the final product with the sleeved SATA Data cables installed and zipped.
http://i11.photobucket.com/albums/a190/Fuganater987/Project Honeycomb/DSC09446.jpg

I'm happy with how they came out. I did the same thing for the other HDD cage but I ran out of heat shrink so I put another order in for it at MDPC-X. My ATX pin remover is also starting to go... I think I need to spend the money and get the good one.

Cheers till next time!

Well done, I wish I could do that (making my own power cables), lol. Looks very nice.

n0tiert · Nov 29, 2011

Fuganater said:
I started making my SATA power cables.

First, I installed all the drives. Put the SATA connectors on them. And started running the cables.

First section done.
http://i11.photobucket.com/albums/a190/Fuganater987/Project Honeycomb/DSC09413.jpg

More done.
http://i11.photobucket.com/albums/a190/Fuganater987/Project Honeycomb/DSC09416.jpg

I had to move a drive down so I could measure the last section correctly.
http://i11.photobucket.com/albums/a190/Fuganater987/Project Honeycomb/DSC09419.jpg

And the final product with the sleeved SATA Data cables installed and zipped.
http://i11.photobucket.com/albums/a190/Fuganater987/Project Honeycomb/DSC09446.jpg

I'm happy with how they came out. I did the same thing for the other HDD cage but I ran out of heat shrink so I put another order in for it at MDPC-X. My ATX pin remover is also starting to go... I think I need to spend the money and get the good one.

Cheers till next time!

you spend alot a time on the case dude, beautiful job !
but then you mess with the sleeves why´s that ?
:ohwell:

overall nice build !

Fuganater · Nov 29, 2011

Sinzia said:
The only thing that doesn't look amazing is the heatshrink... they're all different lengths.

Yes I know. I had some bad cuts. Off by a mm or 2. I might redo it but no one will see it once installed into the system.

Chevalr1c said:
Well done, I wish I could do that (making my own power cables), lol. Looks very nice.

Anyone can! This was my first time making all of them. You never know what you can or can't do until you try.

n0tiert said:
you spend alot a time on the case dude, beautiful job !
but then you mess with the sleeves why´s that ?

overall nice build !

As I said, they won't be seen but I might redo them. Thanks for watching!

de.das.dude · Nov 29, 2011

you should maintain perfection lol. i think you can still carefully cut out and level the heatshrinks.

Fuganater · Nov 29, 2011

de.das.dude said:
you should maintain perfection lol. i think you can still carefully cut out and level the heatshrinks.

Ya I've done that before. Maybe I'll give that a go.

PopcornMachine · Nov 29, 2011

Geesh, people are picky 'round here. :laugh:

Fuganater · Nov 30, 2011

PopcornMachine said:
Geesh, people are picky 'round here.

Ha! I'll have to look at some of their worklogs and see if they can do better

n0tiert · Nov 30, 2011

Fuganater said:
Ha! I'll have to look at some of their worklogs and see if they can do better

yeeeah, kickoff for worklog flames , lol

no i really love the details and fine arts on this project, the only part is what i see, that there wasn´t enough time taken as for the rest ..... my thought, i have same little probs on my own mod.....

hmmm one question m8, is there no mainboard pwm cooler ?

de.das.dude · Nov 30, 2011

Fuganater said:
Ha! I'll have to look at some of their worklogs and see if they can do better

i dont even have sleeving here in india

Fuganater · Nov 30, 2011

n0tiert said:
yeeeah, kickoff for worklog flames , lol

haha ya

n0tiert said:
hmmm one question m8, is there no mainboard pwm cooler ?

I don't get what you mean...

n0tiert · Nov 30, 2011

Fuganater said:
haha ya

I don't get what you mean...

i mean the mainboard cooler for the vrm/pwn ? wasn´t there none ?

Fuganater · Nov 30, 2011

It only has heatsinks on the SB and NB.

System Name	Rage
Processor	Intel i7 2600K
Motherboard	Asus Sabertooth P67
Cooling	Custom Watercooling
Memory	8GB G.Skill
Video Card(s)	Dual EVGA GTX 560Ti
Storage	2x SATA3 1TB Western Digital, 1x SATA3 320GB Wester Digital
Display(s)	Dual 22" Chimei
Case	HAF X Modded
Audio Device(s)	Onboard FTW!
Power Supply	Corsair 750W
Software	Windows 7 Professional 64-bit

System Name	Monke \| Work Thinkpad\| J1nnx took Old Monke
Processor	Ryzen 5600X \| Ryzen 5500U \| FX8320
Motherboard	ASRock B550 Extreme4 \| ? \| Asrock 990FX Extreme 4
Cooling	240mm Rad \| Not needed \| hyper 212 EVO
Memory	2x16GB DDR4 3600 Corsair RGB \| 16 GB DDR4 3600 \| 16GB DDR3 1600
Video Card(s)	Sapphire Pulse RX6700XT 12GB \| Vega 8 \| Sapphire Pulse RX580 8GB
Storage	Samsung 980 nvme (Primary) \| some samsung SSD
Display(s)	Dell 2723DS \| Some 14" 1080p 98%sRGB IPS \| Dell 2240L
Case	Ant Esports Tempered case \| Thinkpad \| Antec
Audio Device(s)	Logitech Z333 \| Jabra corpo stuff
Power Supply	Corsair RM750e \| not needed \| Corsair GS 600
Mouse	Logitech G400 \| nipple
Keyboard	Logitech G213 \| stock kb is awesome \| Logitech K230
VR HMD	;_;
Software	Windows 10 Professional x3
Benchmark Scores	There are no marks on my bench

System Name	Rage
Processor	Intel i7 2600K
Motherboard	Asus Sabertooth P67
Cooling	Custom Watercooling
Memory	8GB G.Skill
Video Card(s)	Dual EVGA GTX 560Ti
Storage	2x SATA3 1TB Western Digital, 1x SATA3 320GB Wester Digital
Display(s)	Dual 22" Chimei
Case	HAF X Modded
Audio Device(s)	Onboard FTW!
Power Supply	Corsair 750W
Software	Windows 7 Professional 64-bit

System Name	Monke \| Work Thinkpad\| J1nnx took Old Monke
Processor	Ryzen 5600X \| Ryzen 5500U \| FX8320
Motherboard	ASRock B550 Extreme4 \| ? \| Asrock 990FX Extreme 4
Cooling	240mm Rad \| Not needed \| hyper 212 EVO
Memory	2x16GB DDR4 3600 Corsair RGB \| 16 GB DDR4 3600 \| 16GB DDR3 1600
Video Card(s)	Sapphire Pulse RX6700XT 12GB \| Vega 8 \| Sapphire Pulse RX580 8GB
Storage	Samsung 980 nvme (Primary) \| some samsung SSD
Display(s)	Dell 2723DS \| Some 14" 1080p 98%sRGB IPS \| Dell 2240L
Case	Ant Esports Tempered case \| Thinkpad \| Antec
Audio Device(s)	Logitech Z333 \| Jabra corpo stuff
Power Supply	Corsair RM750e \| not needed \| Corsair GS 600
Mouse	Logitech G400 \| nipple
Keyboard	Logitech G213 \| stock kb is awesome \| Logitech K230
VR HMD	;_;
Software	Windows 10 Professional x3
Benchmark Scores	There are no marks on my bench

System Name	Rage
Processor	Intel i7 2600K
Motherboard	Asus Sabertooth P67
Cooling	Custom Watercooling
Memory	8GB G.Skill
Video Card(s)	Dual EVGA GTX 560Ti
Storage	2x SATA3 1TB Western Digital, 1x SATA3 320GB Wester Digital
Display(s)	Dual 22" Chimei
Case	HAF X Modded
Audio Device(s)	Onboard FTW!
Power Supply	Corsair 750W
Software	Windows 7 Professional 64-bit

System Name	Vulcan
Processor	i6 6600K
Motherboard	GIGABYTE Z170X UD3
Cooling	Thermaltake Frio Silent 14
Memory	16GB Corsair Vengeance LPX 16GB (2 x 8GB)
Video Card(s)	ASUS Strix GTX 970
Storage	Mushkin Enhanced Reactor 1TB SSD
Display(s)	QNIX 27 Inch 1440p
Case	Fractal Design Define S
Audio Device(s)	On Board
Power Supply	Cooler Master V750
Software	Win 10 64-bit

System Name	FragBox
Processor	Intel Core i7 2600K @ 5.0GHz/1.45 volts
Motherboard	Asus P8Z77 WS
Cooling	Custom CPU loop
Memory	Kingston 12GB DDR3 1600
Video Card(s)	Galaxy GTX 680/Zotac GTX 680 in SLi/EVGA GTX 650Ti
Storage	2 Vertex 3 120's, raid 0, 2 Seagate Momentus XT 500GB's in raid 0, 1 Hitatchi 2TB for backup
Display(s)	3 Acer S232HLX2 in nvidia surround
Case	Corsair C70 White
Audio Device(s)	Onboard
Power Supply	Corsair AX1200
Software	Win 7 x64 Pro

System Name	ap201 \| Odroid N2+ \| NUC
Processor	AMD Ryzen 5 3600 \| Amlogic S922X \| Intel Core i5-7260
Motherboard	Gigabyte B550M DS3H \|Odroid N2+ \| NUC Board 7
Cooling	Inter-Tech Argus SU-200, 3x Arctic P12 case fans \| stock heatsink + fan \| stock HSF
Memory	Gskill Aegis DDR4 32GB \| 4 GB DDR4 \| 16 GB DDR4
Video Card(s)	Sapphire Pulse RX 6600 (8GB) \| Arm Mali G52 \| Iris Plus 640
Storage	SK Hynix 240GB, Sam. 840 + 850 EVO (2x (250 GB)\| Samsung 850 Evo 500GB \| WD Green 240 GB
Display(s)	AOC G2260VWQ6 \| LG 24MT57D \|
Case	Asus Prime 201 \| Stock case (black version) \| Stock case
Audio Device(s)	integrated
Power Supply	BeQuiet! Pure Power 11 400W \| 12v barrel jack \| 19V laptop brick (Asus)
Mouse	Logitech G500 \|Steelseries Rival 300 \| no-name ergo mouse
Keyboard	Qpad MK-50 (Cherry MX brown)\| Blaze Keyboard
Software	Windows 10, EndeavourOS \| Gentoo Linux \| EndeavourOS

System Name	Shaman of Sexy
Processor	AMD Phenom II X4 955 BE@4Ghz EK Supreme Block
Motherboard	M3A79-T Deluxe Anfi-Tech Waterblocks
Cooling	Magicool 360 + 120 + 120 Slim scythe slipped Laing DDC-1/T
Memory	4GB Corsair Dominator CM2X2048-8500C5D
Video Card(s)	Sapphire ATI Radeon HD 4870 X2 EK 4870 X2 Block
Storage	RAID 0 Seagate
Display(s)	Samsung 226BW 22"
Case	CoolerMaster Cosmos RC-1000 in mod progress
Audio Device(s)	onboard
Power Supply	Coba Nitrox 750W
Software	Windows 7 Ultimate
Benchmark Scores	http://service.futuremark.com/compare?3dmv=1056967

Project: Honeycomb

New Member

Pro Indian Modder

New Member

Pro Indian Modder

New Member

New Member

Pro Indian Modder

New Member

Pro Indian Modder

New Member

Pro Indian Modder

New Member

Pro Indian Modder

New Member

New Member

Pro Indian Modder

New Member

New Member