Test Setup

All measurements were performed using two Chroma 6314A mainframes equipped with the following electronic loads: six 63123A [350 W each], one 63102A [100 W x2], and one 63101A [200 W]. The aforementioned equipment is able to deliver 2500 W of load, and all loads are controlled by a custom-made software. The AC source is a Chroma 6530 capable of delivering up to 3 kW of power. We also used a Rigol DS2072A oscilloscope kindly sponsored by Batronix, a Picoscope 3424 oscilloscope, a Picotech TC-08 thermocouple data logger, two Fluke multimeters (models 289 and 175), a Keithley 2015 THD 6.5 digit bench DMM, and a lab grade N4L PPA1530 3-phase power analyzer along with a Yokogawa WT210 power meter. We also included a wooden box, which, along with some heating elements, was used as a hot box. Finally, we had at our disposal three more oscilloscopes (Rigol VS5042, Stingray DS1M12, and a second Picoscope 3424), and a Class 1 Bruel & Kjaer 2250-L G4 Sound Analyzer we equipped with a type 4189 microphone that features a 16.6-140 dBA-weighted dynamic range. You will find more details about our equipment and the review methodology we follow in this article. We also conduct all of our tests at 40°C-45°C ambient to simulate the environment seen inside a typical system more accurately, with 40°C-45°C being derived from a standard ambient assumption of 23°C and 17°C-22°C being added for the typical temperature rise within a system.

We use a GPIB-USB controller to control the Chroma 6530 source, which avoids its incredibly picky serial port. This controller was kindly provided by Prologix.



To protect our super expensive Chroma AC source, we use an OLS3000E online UPS with a capacity of 3000VA/2700W.

Primary Rails Load Regulation

The following charts show the voltage values of the main rails, recorded over a range from 60 W to the maximum specified load, and the deviation (in percent) for the same load range.

5VSB Regulation

The following chart shows how the 5VSB rail deals with the load we throw at it.

Hold-up Time

Hold-up time is a very important PSU characteristic and represents the amount of time, usually measured in milliseconds, a PSU can maintain output regulations as defined by the ATX specification without input power. In other words, it is the amount of time a system can continue to run without shutting down or rebooting during a power interruption. The ATX specification sets the minimum hold-up time to 16 ms with the maximum continuous output load. In the following screenshot, the blue line is the mains signal and the yellow line is the "Power Good" signal. The latter is de-asserted to a low state when any of the +12V, 5V, or 3.3V output voltages fall below the undervoltage threshold, or after the mains power has been removed for a sufficiently long time to guarantee that the PSU cannot operate anymore.



The hold-up time exceeded 16 ms, which is fine.

Power Good Signal

According to the ATX specification, PWR_OK is a "power good" signal used by the system's power supply to indicate that the +5VDC, +3.3 VDC, and +12VDC outputs are above the PSU's under-voltage thresholds. Since the ATX 1.2 revision, ripple at PS_ON and PWR_OK must not exceed 400 mV.


The screenshot above clearly shows that ripple, PWR_OK, is well above the 400 mV limit.

Inrush Current

Inrush current or switch-on surge refers to the maximum, instantaneous input-current drawn by an electrical device when it is first turned on. Because of the charging current of the APFC capacitor(s), PSUs produce large inrush-current right as they are turned on. Large inrush current can cause the tripping of circuit breakers and fuses and may also damage switches, relays, and bridge rectifiers; as a result, the lower a PSU's inrush current right as it is turned on, the better.



Inrush current was normal for the PSU's capacity.

Load Regulation and Efficiency Measurements

The first set of tests revealed the stability of the voltage rails and the HG750's efficiency. The applied load was equal to (approximately) 10%-110% of the maximum load the PSU can handle, in 10% steps.
We conducted two additional tests. In the first test, we stressed the two minor rails (5V and 3.3V) with a high load while the load at +12V was only 0.10 A. This test reveals whether the PSU is Haswell ready or not. In the second test, we dialed the maximum load the +12V rail can handle while the load on the minor rails is minimal.

Load regulation was good enough at +12V and 5V, but loose on the other rails. We would like to see better load regulation at 3.3V, although it isn't as important a rail as the others since modern systems only tax it lightly. Efficiency between 20%-100% of the maximum-rated capacity is high enough, although not as high as with other PSUs of the same category.

As you will notice by looking at the table above, passive mode didn't last long, and the fan spun at high speeds during the third test, which produced a lot of noise. With higher loads under tough conditions, the fan became annoyingly loud, exceeding 50 dBA at 80% load. If you intent to push this PSU, you had better get yourself a pair of earplugs—you would definitely need them.