Share your AIDA 64 cache and memory benchmark here

[Dinnercore]

So my Quad-Channel can't go too low with latency, atleast not on my daily settings. But the bandwidth is ok.

Moved here from the competition thread, I clicked the wrong title <-<

 

[glnn_23]

Couple of runs 3900x in a C8H. TridentZ 4266c19

3800c14. and 4400c16

 

[Dinnercore]

Sorry for posting again so quickly but that 100GB/s write mark was so close, I just had to make it work.

Small improvements on the subtimings, another tick down on read-to-write delay and I got it:

NB is still 3.1 GHz it just dropped to idle clock.

 

[dont whant to set it"']

@Dinnercore quick , someone stop him , unplug the ram chiller or something.
Superb.

 

[Dinnercore]

@Dinnercore quick , someone stop him , unplug the ram chiller or something.
Superb.

ram chiller?! I wish I had that. This is on daily voltage 1.5V and memtest stable.

 

[NoJuan999]

Sorry for posting again so quickly but that 100GB/s write mark was so close, I just had to make it work.

Small improvements on the subtimings, another tick down on read-to-write delay and I got it:
View attachment 157949

NB is still 3.1 GHz it just dropped to idle clock.

I am seriously jealous !!!!!

 

[Arctucas]

Been trying to get Copy into the 60s with Read and Write at 24/7 settings; 50x CPU multiplier, 100MHz BClk, 47x Ring multiplier.

 

[Dinnercore]

I'm spamming this thread but I can't stop tweaking:

Found out I can use 1T just as well, also cut down the refresh cycles more aggressive.

Despite AIDA reading 4000 I'm on 4088 now thanks to BCLK adjustment. Straight up 4200 seems to upset my CPU's IMC which I limited to 1.2V. The auto-setting suggests 1.33V but I'm not sure if I want to go that high on this CPU.

 

[RandomSadness]

Anyone with a 3950X?
Coming from a 7700K, it's a life-changing upgrade.
I feel like my memory latency is insane. Granted, this is from a 64 GB 3600 C18 kit that I just moved to 4133 with the same timings, but still...

 

[Dinnercore]

Anyone with a 3950X?
Coming from a 7700K, it's a life-changing upgrade.
I feel like my memory latency is insane. Granted, this is from a 64 GB 3600 C18 kit that I just moved to 4133 with the same timings, but still...View attachment 159107

Maybe try running 3600 or 3733 with tighter timings to sync better with fabric clock of 1800 or 1866 MHz.

 

[EarthDog]

Maybe try running 3600 or 3733 with tighter timings to sync better with fabric clock of 1800 or 1866 MHz.

Exactly.

You should be in the upper 60ns latency when it's tied 1:1 with IF.

This platform isn't intel so latency will always be higher. On z490 ddr4 3600 is upper 40ns latency. You won't get much if at all above 3800 while matching 1:1 to reduce that latency.

I suggest reading an oc guide so you know whats going on.

 

[Deleted member 197986]

 

[johnspack]

Wow, my old xeon is starting to show it's age....

 

[dont whant to set it"']

Just about topped out with the 1:1 ratio between Fclk:Mclk

 

[heky]

Just about topped out with the 1:1 ratio between Fclk:MclkView attachment 159393

What do you mean with "topped out"? Are you saying the IF of the chip can´t go higher than 1600mhz or is the memory just that bad?

 

[dont whant to set it"']

@heky
It's ram from the yee old days of grandpa Skylake , this on the fun side note.
I got it booting a couple times at 3333mhz 1:1 and benched it with the read numbers beeing in the same mid 47k MB's while latencies at 71ns access times, not at all game stable and this was back in the days in which I had no clue the mb was 35 mV overvolting whatever it was set in the bios for Dram voltage , I've put trough these sticks 1.55v with no results, notw them dimms are at a "balmy 1.365 too 1.38V.
All in all considering it's a B350 Chipset mb !.
Le: yeah it's that "bad" , £65 MB , £30 RAM , heck load of fun.

 

[The Foldinator]

lol

 

[Duvar]

Because of the board, i cant go any higher than 3900MHz... Even with 1.6V RAM 1.35V SA/IO and CL20 i cannot even boot^^
It is a T-Tpopogy Board and i have only 2 dimms, this is pretty much the best i could do with that crap board...

 

[Tatty_Two]

Just got these yesterday now showing in my specs, this is just a quick run at XMP, been playing around a bit but can't decide if it's best to run them at 4133mhz CL17 2T or 4000mhz same timings but @1T, both at 1.4v, this is just for starters (hopefully), when I have more time I wanna tweak more at higher speeds and tighten more at lower to find the best balance, want to try and keep within 1.45v, ...………..

 

[Tatty_Two]

A first stab, managed to get them at 4133mhz @ 17-17-17-34 @2T on 1.4v, rebooted and ran a couple of stress tests and a game for a couple of hours, then went back into Bios and noticed that the SA voltage was on auto and showing 1.45v!! and VCCIO was at 1.3v, manually dropped them to 1.20v each and saw a minor performance improvement, still a lot to test but need more time, CPU at stock as I like to let the Thermal paste bed in for a couple of weeks, surprisingly CPU voltage on auto currently and reacting very well, rarely even hits 1.3v in any threaded scenario and with that running cool on a middle of the road 240mm AIO, highest multithreaded temps of 65c ...……...

Edit: Got 4000mhz stable at CL16-17-17-34 2T @ 1.4V but slightly lower scores so will stick with the 4133mhz CL17 for now.

 

[RandomSadness]

Exactly.

You should be in the upper 60ns latency when it's tied 1:1 with IF.

This platform isn't intel so latency will always be higher. On z490 ddr4 3600 is upper 40ns latency. You won't get much if at all above 3800 while matching 1:1 to reduce that latency.

I suggest reading an oc guide so you know whats going on.

Unfortunately this is the best I could do

 

[Mobile_Kimchee]

Hey all, I'm new to this but any help would be greatly appreciated! This is my first attempt at overclocking my ram manually and my head is about to explode. I think I squeezed out as much as I can but really don't know. I am stable with these setting 2 hours of Karhu memtest and 12 hours of aida 64.
MSI Godlike Z390
Intel I9 9900k
EVGA 2080 TI xc
Corsair Dominator RGB Platinum DDR4 4000 C19 (2x16) have 4 sticks but cant get all 4 to post @4000MHz
EKWB water cooled CPU and GPU
2 x 1 TB Samsung 970 plus

 

[cucker tarlson]

A first stab, managed to get them at 4133mhz @ 17-17-17-34 @2T on 1.4v, rebooted and ran a couple of stress tests and a game for a couple of hours, then went back into Bios and noticed that the SA voltage was on auto and showing 1.45v!! and VCCIO was at 1.3v, manually dropped them to 1.20v each and saw a minor performance improvement, still a lot to test but need more time, CPU at stock as I like to let the Thermal paste bed in for a couple of weeks, surprisingly CPU voltage on auto currently and reacting very well, rarely even hits 1.3v in any threaded scenario and with that running cool on a middle of the road 240mm AIO, highest multithreaded temps of 65c ...……...

View attachment 160597

Edit: Got 4000mhz stable at CL16-17-17-34 2T @ 1.4V but slightly lower scores so will stick with the 4133mhz CL17 for now.

here's mine,same sticks,same settings
did you try lowering trfc ?

 

[Tatty_Two]

No, not had the time to play with them anymore yet, might get some this Saturday, I just dialled those in when I installed the sticks because I knew they would work, damn this retirement business is busy! Will try and have a go this weekend.

 

[cucker tarlson]

No, not had the time to play with them anymore yet, might get some this Saturday, I just dialled those in when I installed the sticks because I knew they would work, damn this retirement business is busy! Will try and have a go this weekend.

default trfc is 550
I dialled 400 and it works.shaved off almost 4ns off your result with a lower ring bus cpu so you may get even lower
update: got them to run 4133 16-16-16-31 at 1.45v,still at 41ns,40ns will be hard to break