Share your AIDA 64 cache and memory benchmark here

[mrthanhnguyen]

 

[Gregix]

^^ @UP
With such a great mobo for memory OC u should do better man. Usually I can see on others APEXses below 35ns area.
OK, I see its 2x16, still this could be 36-37 max.

Below my results, mind u, my mobo/IMC combination does not allow to play with primary timings, so it is almost stock. BUT, all secondary, and even RTL can do trick, so instead 42ns aida score, u can see 38ns area.

But my daily driver is 4100c15(no problem here, but it needed some cooling on RAM).
Its Prime95 non AVX FFT 112 stable, runs stable aida64 system stress(with GPU for more heat) + TMv5 anta extreeme/ollie in the same time, game stable (BFV and Alien Isolation VR, etc).

 

[glnn_23]

3900xt and 16Gb Team memory

 

[mrthanhnguyen]

^^ @UP
With such a great mobo for memory OC u should do better man. Usually I can see on others APEXses below 35ns area.
OK, I see its 2x16, still this could be 36-37 max.

Below my results, mind u, my mobo/IMC combination does not allow to play with primary timings, so it is almost stock. BUT, all secondary, and even RTL can do trick, so instead 42ns aida score, u can see 38ns area.

But my daily driver is 4100c15(no problem here, but it needed some cooling on RAM).
Its Prime95 non AVX FFT 112 stable, runs stable aida64 system stress(with GPU for more heat) + TMv5 anta extreeme/ollie in the same time, game stable (BFV and Alien Isolation VR, etc).

Here is your 37 latency

 

[md2003]

16gb ddr4 dual channel $68 kit:

 

[md2003]

Sadly, i can't edit my previous post. After few tweaking and suggestions from @Gregix, here are some updated results as comparison to my previous:
memtest stable:

and high freq ss

As it looks, setting FSB higher than 101 negatively affects ram speeds overclockability and stability.

 

[Gregix]

Patriots with tighter subtimings, cannot touch primaries, does not boot.
And an old z97 + 5775c combo on ddr3 1600@2200

 

[Ja.KooLit]

 

[LiquidTrance]

Gaming PC: 9900K@5.25GHz HT/OFF 1.38v 4x8GB@3933MHz 15-14-14-30-2T 1.5v/Vdimm 1.3v/VccSA 1.3v/VccIO

 

[nicke85]

Here is my Medion Erazer X7853 MD60605 ,7820hk 1070GTX with 32gb 2x16gb Crucial SO-DIMM 3200Mhz at lower 3000
not bad at all in 2020 (still have 2x free slots for ram dimms)
want to see somebody with ryzen 7 4800H to can compare

 

[Toothless]

 

[kamilos876]

HyperX Predator RGB, DDR4, 16 GB, 4000MHz, CL19 (HX440C19PB3AK2/16 )
@4200 16-16-16-36 1.45V

What should I do to have less than 40 latency?

 

[Gregix]

Bump ring ratio, to 45x. More CPU oc itself helps too. But mainly, do secondary and tertiary tweaking. For more info check overclkockers 24/7 ddr4 intel stability thread, first page and from like 1100 up. Mind u it is time consuming. But worth it as games/all run smoother. Ur read speed is too low, write somewhat too, copy should be like 3000mb/s less than read/write. So there is room to improve.

 

[Arctucas]

Got a new kit; GSkill F4-4000C19D-32GTZSW.

 

[Deleted member 178884]

Just tuned the new laptop a bit, pretty impressed with it haven't pushed further yet.

 

[EarthDog]

Just tuned the new laptop a bit, pretty impressed with it haven't pushed further yet.

3600 CL 20? On AMD too? Oof....!

 

[Deleted member 178884]

3600 CL 20? On AMD too? Oof....!

That's a laptop - it's limited to 1.2V set as Der8aeur decided to LN2 run the XMG Apex 15 without clevo's consent who decided to not make the unlocked BIOS public - 3600CL20 with 1800IF is also miles better than 3200CL22 with 1600IF (what basically every AMD laptop uses) and what this laptop uses at stock.

 

[LiquidTrance]

Updated CPU/Memory Overclock
i9-9900K@5.05GHz - 4.75GhzCache - 8C/16T - 1.35v/load(avx2) - 4x8GB@3933MHz 1.5v

 

[Arctucas]

Been playing with my 32GB kit.

 

[LiquidTrance]

Been playing with my 32GB kit.

View attachment 169325

Seeing cas 16 makes me want to tinker with my ram some more because I want 4266 but i haven't been able to figure out how to stabilize it or get good rtls/iols for 4000+ at any cas so I just downclock to 3933 >< womp womp. Have fun tinkering, it's a lot of fun. If there is one thing i've learned about the process, it is to have patience. Sometimes it takes time for things to click if you know what i mean.

 

[mouacyk]

Seeing cas 16 makes me want to tinker with my ram some more because I want 4266 but i haven't been able to figure out how to stabilize it or get good rtls/iols for 4000+ at any cas so I just downclock to 3933 >< womp womp. Have fun tinkering, it's a lot of fun. If there is one thing i've learned about the process, it is to have patience. Sometimes it takes time for things to click if you know what i mean.

Yeah, it's like this fleeting enlightenment of understanding out the universe works.

 

[LiquidTrance]

Yeah, it's like this fleeting enlightenment of understanding out the universe works.

Could you be specific? i don't quite follow what you are saying.

 

[Arctucas]

Seeing cas 16 makes me want to tinker with my ram some more because I want 4266 but i haven't been able to figure out how to stabilize it or get good rtls/iols for 4000+ at any cas so I just downclock to 3933 >< womp womp. Have fun tinkering, it's a lot of fun. If there is one thing i've learned about the process, it is to have patience. Sometimes it takes time for things to click if you know what i mean.

What do you consider good RTLs/IOLs?

 

[LiquidTrance]

Had to remove this information, shared too much.

 

[Arctucas]

Appears you have done quite a bit of testing.

I am at 60/61 and 6/6 @ 16-16-16-34 2T 4000MHz.

This kit will not train above 4000MHz, even though it is 4000MHz XMP2. Not on the QVL, probably lucky it boots at all...