Aorus X570 Master

[jesdals]

Testing the new F31l bios - it seems less stable and did not give access to Infinity fabric above 1900MHz, some strange bugs - enabling smart access memory - made it disable all my nvme drives as a boot option, thus cycleing right back into bios on restart.

F31j seems more stable and less buggy

 

[TheLostSwede]

It seems that I hit a Infinity wall again, this time its not possible to go past 1900MHz. I have tried 1933, 1966 and 2000MHz, with all the trickery I could pull out

Btw no gaming advantage running 1900MHz
View attachment 177360

Isn't that an AGESA limitation at the moment and AMD has promised to improve this early next year?

 

[jesdals]

The F31l seems to be hit by the WHEA errors

Not haveing a 6000 series GPU I think the F31j is the better choise with 5000 series cpu

Decided to flash back to the F31j with same settings no WHEA error so far - going to make a clean reinstall with the new WD SN850 in the upcomming days, to see if it makes any difference in performance. And installing a Arctic Liquid freezer II 360 AIO (if it will fit in my Fractal Meshify C)

 

[jesdals]

Did a fresh install on my new WD SN850 2Tb drive

Compared with my old Gigabyte Aorus 2Tb its pretty decent

And my Corsair MP600 1 Tb

Installing a new Arctic 360 aio was a pain and did not improve temps. I will test for some time before changeing flow on the rad coolers

The fresh install of windows gave a minor boost in Division 2. But even after installing chipset drivers there no Ryzen powerplan?

 

[tabascosauz]

@jesdals Robert Hallock said couple of weeks ago there isn't and won't be any power plan visible for Ryzen 5000

 

[jesdals]

That explaine wy it disapeard after the reinstall

Boost clocks havent been above 5GHz on more than one core yet, but will se after a couple of days with the new cooler and the Repaste with Noctua NT-H2 paste

 

[jesdals]

Did a change from pushing out to intake on the rad in front, still not able to keep the beast under 90c during GPUz stress test - funny to compare this to the two recent builds I have made with Lian Li Lancool II (one the new Mesh Performance edition) and 3600x/xt cpu´s that ran for more than 8 ours without getting over 65c - 2 compute cores take something bigger and cooler than the Arctic Liquid Freezer II 360 - but still a nice AIO. I can not recommend building with 360 front in the Meshify C - its a pain to fit it in.

Under full load in the GPUz stress test it would drop beneath 12000 points in the test score after 15-20 minutes and cores will go under 4,2ghz

 

[jesdals]

It looks like Gigabyte has pulled all the F31 versions of the bios

 

[Chomiq]

It looks like Gigabyte has pulled all the F31 versions of the bios

F31o
2‎020/12/03

 

[mstenholm]

F31o
2‎020/12/03

Did you test it asked the man still on 11beta?

 

[Chomiq]

Did you test it asked the man still on 11beta?

I'm still on F30.

 

[mstenholm]

I run 100%, 24/7 and Linux and all is well around 4.140 MHz all core and I don’t fix something unless it’s not broken or if I can expect a decent improvement.

 

[Calmmo]

Updated to F31o as i'm waiting on a 5900x (should ship tomorrow but due to work i doubt ill be able to get it)
Noticed maaasive lag/delays on starting programs etc. Updated to the latest chipset drivers and things seemd to be sorted but i could still notice some delay when starting up things.
Definitely don't recommend anyone updates to any agesa 1.1.1.0 on the master based on personal experience (admittedly amd/Robert Hallock have stated that unless you're on Vermeer there's no reason to update bios, but still, good to know it can actually be detrimental to performance)

I'm still on F30.

Based on the above, you should stick with it, I had no perf issues with F30 my self on the 3900x

 

[jesdals]

Running stable on F31j, but did not have any succes with the new PBO curve settings https://www.techpowerup.com/forums/threads/amd-curve-optimizer-any-guides-experience.275640/

 

[jesdals]

Did som pre F1o testing today

Still hopeing for 2000MHz infinity

New hardware needs new bios for SMART

 

[jesdals]

Enabling SAM took som effort had to convert my windows partion to get it bootable from bios

I had to use Windows powershell in admin mode to gove there - be carefull - you might end up with data loss so do backup
you can get to the windows powershell by pressing windows tab + x

After this you can enable SAM in bios under the IO menu

But theres no way to see it enabled in windows, shame that theres no where in the driver its showing.

F31o bios seems stable - I am still not able to push beyond 1900MHz Infinity fabric, but will do some memory testing to se if I can tighten my settings

 

[jesdals]

The SAM is very buggy, did som changes on my memory settings and suddently i couldnt see my nvme drives again in the boot option. I had to reset bios a coupple of times before I did manage to get it back again. So still very buggy.

 

[oxrufiioxo]

Hopefully by the time I secure a 5950X that shits all fixed or I'm swapping it for rocket lake

 

[jesdals]

New bios F31q - SAM works (perhaps because still not able to see if it actually runs in windows - but bootable), no improvement on Infinity fabric range - still capped at 1900MHz - will do som memory testing in the upcomming days

 

[INSTG8R]

New bios F31q will do some testing with the SAM setting on that

Thanks for the heads up I checked late yesterday was still on O. I'm anxiously awaiting my 5600X(didn't check stock when I bought it)So January...

 

[Mario5]

hi all
please maybe you can help me
I upgraded to F31q (from F31o) and after few hours, after sleep mode, i dont know how, it went back to F31o and everything goes on defaultv(xmp profile - 2133 mhz also, fans speed etc)
I have X570 Master with 5800x with 32 GB Corsair RGB 3200mhz and strange thing, when i power on the pc, fans go crazy in idle mode, now i have F2 code on motherboard, when i stress test with AMD Master, after the test everything goes to normal , quiet pc and temps go lower. Want to mention that i upgraded again the bios to F31q. Can someone help me?
exactly in this moment (after sleep mode) i have now F8 code but F31q bios (not F31o like before)
want to say that before first upgraded bios i had this problems (with xmp,fans, temps)
i am really nervous and i dont know what to do...

 

[jesdals]

hi all
please maybe you can help me
I upgraded to F31q (from F31o) and after few hours, after sleep mode, i dont know how, it went back to F31o and everything goes on defaultv(xmp profile - 2133 mhz also, fans speed etc)
I have X570 Master with 5800x with 32 GB Corsair RGB 3200mhz and strange thing, when i power on the pc, fans go crazy in idle mode, now i have F2 code on motherboard, when i stress test with AMD Master, after the test everything goes to normal , quiet pc and temps go lower. Want to mention that i upgraded again the bios to F31q. Can someone help me?
exactly in this moment (after sleep mode) i have now F8 code but F31q bios (not F31o like before)
want to say that before first upgraded bios i had this problems (with xmp,fans, temps)
i am really nervous and i dont know what to do...

Somehow you managed to get into the second bios - you can save your settings in bios and i usally make the first save as bios 1 so I can se if I am on the first or second bios. If thats not the case you could have a faulty battery on the board and try to change it. But try to save your settings again save the setup and rember to mark the first saving so You can see if it boot on the secondary bios. You will find recommendation for settings earlier in this thread an most will still applay to bios F31o/q and your 5800x

 

[jesdals]

New F31 (final bios), trying the latest driver and found some interesting new PBO settings - new max boost 500MHz

 

[Caring1]

New F31 (final bios), trying the latest driver and found some interesting new PBO settings - new max boost 500MHz
View attachment 182647

That memory Voltage

 

[jesdals]

That memory Voltage

Thats allow CL14 at 1900MHz

PBO boost with above settings