Aorus X570 Master

[neko77025]

So some progress here. Got another Aorus Master from Amazon and, wouldn't you know it, exately the same issue. 07/D7 Post message. Now the question is does this suggest the memory is faulty or the CPU or just further issues with the mobo. Never had these problems with, ahem, Intel...

Memory is 2x8Gb Corsair Vengence Pro (CMW16GX4M2C3200C16W) which is on the QVL.

Gigabyte support are appalling, basic response was "erm, don't know, send it back to the retailer"

I have tried many types of memory and seen others use other brands I have not tried with the same issue ... I really dont think , its the memory at this point. As far as CPUs ... I have seen it on 3700,3800 and 3900... inless AMD has A huge issue with only the gigabyte boards ... ( i dont see anything like this with non-gigbyte). That leaves gigabyte .. some of us have the issue amd some dont ... I think their is A bad batch ..

and this is one of the worst experiences I have had building computers .. Have been doing this 1997 .. I have had issues, have done more then my fair share of RMAs ... but this is something else ... Like .. I feel bad in a few ways ... feel dumb that i cant solve it , feel bad having to call up newegg and RMA almost everything .. feel so confused ... and ripped off . I have to call Newegg again for another RMA .. this will be the 3rd in like 2- 3 weeks time .. however 2 were motherboard .. should not of RMAed the RAM ...

The gigabyte support was so bad, A few years back I had to use them for another motherboard .. and it was not bad at all .. And i know the guy back then was in the USA ... when you call now .. they are somewhere in Asia ... very rude and just want to get the call over with. ( i assume they are gettn alot of calls about this )

as far as this motherboard goes ... I do plan on exchanging it for something else .. going too wait till I have a few days left .. just to see and use that time to pick something else ... sucks cause this really looked to be the best of all the boards

 

[exclusive_muppet]

I've order more memory as a test, was going to at some point anyway. If that fails I'm going to try and RMA the CPU.

Might RMA the whole lot and build a i9-9900k system. Very disappointed.

 

[Zach_01]

... but now i know other people have the same issue with 3700x,3800x and 3900x ( have not seen any 3600/x)

Aorus Pro here with 3600...
Post #62

My Corsair ram has samsung b-dies. The system worked just fine for 10 days since I first start it... and I had this issue 2~3 hours (5~6 restarts in between) after flashing to the last UEFI version. So I Qflashed it to previous version. So far for the last 2 days everything looks fine.

Is it true that AGESA 1.0.0.4 is coming on September 10th?

 

[kartoffelotto]

i have a weird issue with my aorus ultra that prevents me from using windows sleep, whenever i try to get my pc back from sleep on the new stable f4 bios, pc gets stuck in a post loop on the ram led (no postcode display on this board). wasnt like that on earlier bios versions. only way to get out of it is the power button, after that i get either a cmos reset or the rescue bios jumps in.

 

[neko77025]

Aorus Pro here with 3600...
Post #62

My Corsair ram has samsung b-dies. The system worked just fine for 10 days since I first start it... and I had this issue 2~3 hours (5~6 restarts in between) after flashing to the last UEFI version. So I Qflashed it to previous version. So far for the last 2 days everything looks fine.

Is it true that AGESA 1.0.0.4 is coming on September 10th?

Yea .. thats the thing .. it seems like its fixed but it comes back ... If you reset your computer A bunch .. I am sure it will show up, no matter what bios ... at this point I just have A USB drive sitting in my Qflash slot .. when it dont turn on i just do that and walk away for 5mins ... .but I will not keep this board ... if the Q-flash+ button ever brakes or stopps working you will be SoL.

 

[TheLostSwede]

F6 UEFI just out. No new AGESA though.

X570 AORUS MASTER (rev. 1.0) Support | Motherboard - GIGABYTE Global

Lasting Quality from GIGABYTE.GIGABYTE Ultra Durable™ motherboards bring together a unique blend of features and technologies that offer users the absolute ...

www.gigabyte.com

 

[Chomiq]

So is master the same as elite when it comes to case fans spinning up to full speed at boot? Anyone knows a way around it?

 

[TheLostSwede]

So is master the same as elite when it comes to case fans spinning up to full speed at boot? Anyone knows a way around it?

Have you gone in to the fan settings and set something like the silent profile?
I can't say I have noticed that.

 

[Chomiq]

Have you gone in to the fan settings and set something like the silent profile?
I can't say I have noticed that.

I'll try that at home.

Till now all I did was to adjust the fan settings with SIV in windows. Didn't touch the UEFI settings, maybe that's why.

 

[jesdals]

I am currently running F6 bios and it seems stable, did som tightning of my memory timings and still running 4500MHz all core using the Pstates setting at 4500MHz and 1.45vcore

 

[TheLostSwede]

Just a heads up on a bug with the F6 UEFI.
There's an issue with CSM which might get you the lovely "missing boot drive" error message.
Nothing is borked with your hardware if you see this.
Go into the UEFI, disabled CSM, reboot and it should work.
This might only be related to NVMe drives and weirdly enough, certain combinations of graphics cards.
Gigabyte is aware of the issue and are working on a fix.

 

[jesdals]

I am currently running F6 bios and it seems stable, did som tightning of my memory timings and still running 4500MHz all core using the Pstates setting at 4500MHz and 1.45vcore

Havent had the issue with the nvme drives yet - nice to know - is still very happy with my setup

 

[TheLostSwede]

F7a seems to have fixed the issue I was seeing, at least so far.
Just curious is this has helped solved everyone else's issues that they were having.

 

[neko77025]

have not had any of my old issues yet ..
on F6 or F7a (crossfingers / knock on wood )

 

[Assimilator]

I had issues with my Z77X-UD5H arbitrarily corrupting its BIOS way back in the day. Good to see some things haven't changed in Gigabyte land.

 

[Cepheiden]

Hello everyone,

just found this thread and it's exactly the same issue I have.
I started out with a 3700x on an x570 MSI MEG ACE and the system worked fine for 2 days. Until one reboot, where it stopped posting.
Funny enough, the MEG ACE gave me the same 07 error with a red CPU LED.
After some troubleshooting I figured it was the board that was broken.
So I replaced it with a x570 Aorus Master. (I am actually quite happy about that, since it has way better quality than the MSI one in terms of material)

However, on the Master I also get a red DRAM LED stuck on the 15 for a short time, followed by a red CPU LED and a 07 code.
My Aorus Master constantly reboots itself, trying to use the other BIOS after the 07 error.
Also holding down the power button to shut down the system doesn't work. Is that normal or an additional fault with my board


This thread is quite interesting.
So you got it to work with the F7a BIOS? Did you flash it with or without the CPU installed?

By now I am thinking about RMA my CPU, but this gave me hope, it's just a board issue.

 

[neko77025]

Hello everyone,

just found this thread and it's exactly the same issue I have.
I started out with a 3700x on an x570 MSI MEG ACE and the system worked fine for 2 days. Until one reboot, where it stopped posting.
Funny enough, the MEG ACE gave me the same 07 error with a red CPU LED.
After some troubleshooting I figured it was the board that was broken.
So I replaced it with a x570 Aorus Master. (I am actually quite happy about that, since it has way better quality than the MSI one in terms of material)

However, on the Master I also get a red DRAM LED stuck on the 15 for a short time, followed by a red CPU LED and a 07 code.
My Aorus Master constantly reboots itself, trying to use the other BIOS after the 07 error.
Also holding down the power button to shut down the system doesn't work. Is that normal or an additional fault with my board


This thread is quite interesting.
So you got it to work with the F7a BIOS? Did you flash it with or without the CPU installed?

By now I am thinking about RMA my CPU, but this gave me hope, it's just a board issue.

The last 10 times I used q flash + I left the every thing as is.. Cuz I was sick of removing the heatsink/ CPU. ...would have 2 remove gpu , noctua nh-d15. ... So stopped doing it.. Flashing worked for me.

 

[Zach_01]

Yeah, don’t RMA it just yet... I still having same post (DRAM LED) issue with my X570 Aorus Pro even with the latest ABBA Bios. Not so often though and most of the times doesn’t need a reflash. It just going on post loop 1-2 times and just resets it self to stock settings. I did have to Qflash back 1-2 times still. Thankfully there is an option to save the setting profiles in usb....

 

[Cepheiden]

Tried it with the F7a BIOS. No luck.
At least the board works for you guys sometimes. It never did for me.

By the way, is it normal that the system can't be shut down by pressing power buttong when the 07 error occurs?
Also which other board could work? Really had it with boards not working

 

[TheLostSwede]

Tried it with the F7a BIOS. No luck.
At least the board works for you guys sometimes. It never did for me.

By the way, is it normal that the system can't be shut down by pressing power buttong when the 07 error occurs?
Also which other board could work? Really had it with boards not working

No, not sometimes, all the time. Apart from a weird glitch with CSM re-enabling itself on the F6 UEFI, I have had zero issues.

The 07 error is related to memory. Most likely something along the lines of the memory controller not being able to initiate properly due to wrong memory timings being set.

 

[Cepheiden]

Thank you for your answer.
I used the memory I have once before on a MSI MEG ACE and there I activated A-XMP, which worked for 2 days and then I got the no post there.
Is it possible that actually fucked up my memory timing defaults on the 2 16gb sticks I am using?

Obviously I can't do anything about memory timings if I can't get into bios on the aorus master.

Maybe getting new memory will fix it?

Edit: I obviously tried resetting CMOS on both boards. A lot of times.

 

[TheLostSwede]

I don't use XMP, as my board won't boot with the default memory timings.
Avoid using odd CAS settings on this board, at least for now, as they don't seem to work.

 

[Cepheiden]

For sure.
Though I don't get to set any timings since I can't even get into BIOS.

I will get new RAM on tuesday, maybe that fixes it.

 

[TheLostSwede]

If you'd read this forum thread, you would've seen that people are using Q-Flash to re-flash the UEFI, then the board works again, for a while.

I can't guarantee different RAM will fix the issue, simply letting you know what the post code means.
According to a friend of mine at Gigabyte, they can't debug this issue on their own and need help from AMD to resolve it fully.
At least, you've confirmed that it's not a Gigabyte exclusive issue, since you had the same problem with an MSI board.

 

[jesdals]

Still on the F5I and F6 bios, but will give the F7a a try today