Corsair VS Series 650 W Review

Name: Corsair VS Series 650 W
Brand: Corsair

crmaris

on Jul 18th, 2019,

in Power Supplies.

Manufacturer: Corsair

Protection Features Evaluation, DC Power Sequencing & EMC Pre-Compliance Testing »

Advanced Transient Response Tests

In these tests, we monitor the response of the PSU in two different scenarios. First, a transient load (10 A at +12V, 5 A at 5V, 5 A at 3.3V, and 0.5 A at 5VSB) is applied to the PSU for 200 ms while the latter is working at 20% load. In the second scenario, the PSU, while working at 50% load, is hit by the same transient load. We measure the voltage drops the transient load causes with our oscilloscope in both tests. Voltages should remain within the regulation limits defined by the ATX specification.

Real-world usage always has a PSU work with loads that change depending on whether the CPU or graphics cards are busy, which makes whether the PSU can keep its rails within the ranges defined by the ATX specification important. The smaller the deviations, the steadier the system will be, which results in less stress being applied to its components.

We should note that the ATX specification requires for capacitive loading during the transient tests, but in our methodology, we chose to apply the worst-case scenario with no extra capacitance on the rails. Although the ATX specifications asks for this capacitance, your system—the mainboard and its other parts—may not provide it, which we have to keep in mind as well.

Advanced Transient Response 20% - 5 Hz
Voltage	Before	After	Change	Pass/Fail
12 V	12.195V	12.058V	1.12%	Pass
5 V	5.042V	4.916V	2.50%	Pass
3.3 V	3.371V	3.176V	5.78%	Pass
5VSB	4.984V	4.933V	1.02%	Pass

Advanced Transient Response 50% - 5 Hz
Voltage	Before	After	Change	Pass/Fail
12 V	12.114V	11.982V	1.09%	Pass
5 V	5.024V	4.887V	2.73%	Pass
3.3 V	3.340V	3.136V	6.11%	Fail
5VSB	4.938V	4.877V	1.24%	Pass

The +12V rail's transient response is good for the price category of this PSU. The only problem is the 3.3V rail, which registered high voltage drops in both tests.

Below are the oscilloscope screenshots we took during Advanced Transient Response testing.

Transient Response at 20% Load

Transient Response at 50% Load

Turn-On Transient Tests

The next set of tests measure the response of the PSU in more straightforward scenarios of transient load, during the power-on phase of the PSU. In the first test, we turn the PSU off, dial the maximum current the 5VSB can output, and switch on the PSU. In the second test, we dial the maximum load +12V can handle and start the PSU while it is in standby mode. In the last test, we dial the maximum load the +12V rail can handle while the PSU is completely turned off (we cut off power or switch the PSU off by flipping its on/off switch) before turning it on through the loader and restoring power. The ATX specification states that recorded spikes on all rails should not exceed 10% of their nominal values (e.g., +10% for 12V is 13.2 V and 5.5 V for 5V).

Ripple Measurements

Ripple represents the AC fluctuations (periodic) and noise (random) found in the DC rails of PSUs. Ripple significantly decreases the life span of capacitors because it increases their temperature; a 10 °C increase can cut into a capacitor's life span by up to 50 percent. Ripple also plays an important role in overall system stability, especially when it is overclocked. The ripple limits according to the ATX specification are 120 mV (+12V) and 50 mV (5V, 3.3V, and 5VSB).

Ripple Measurements - Corsair VS650
Test	12 V	5 V	3.3 V	5VSB	Pass/Fail
10% Load	6.5 mV	7.7 mV	19.2 mV	14.0 mV	Pass
20% Load	9.2 mV	8.4 mV	21.1 mV	16.4 mV	Pass
30% Load	10.5 mV	9.2 mV	21.7 mV	16.7 mV	Pass
40% Load	13.3 mV	10.3 mV	25.5 mV	16.3 mV	Pass
50% Load	15.4 mV	10.8 mV	28.2 mV	19.1 mV	Pass
60% Load	18.6 mV	11.4 mV	32.0 mV	21.3 mV	Pass
70% Load	22.4 mV	12.7 mV	33.2 mV	21.7 mV	Pass
80% Load	25.2 mV	14.1 mV	37.5 mV	19.8 mV	Pass
90% Load	27.1 mV	15.8 mV	40.7 mV	19.6 mV	Pass
100% Load	38.7 mV	23.5 mV	44.4 mV	24.1 mV	Pass
110% Load	46.0 mV	27.0 mV	47.2 mV	25.8 mV	Pass
Crossload 1	15.2 mV	41.0 mV	28.5 mV	17.9 mV	Pass
Crossload 2	39.4 mV	30.1 mV	37.9 mV	16.7 mV	Pass

Ripple suppression is good on all rails but 3.3V. I would like to see readings below 40 mV on 3.3V. That said, I ran this tests at >40 °C even though the unit's temperature rating is 30 °C.