Ghetto Mods

[ThrashZone]

Just going through some old threads, PC ATM fro 2008. The poster has not been seen sense 2012. He used Image shack so the pictures are still there.
Sure would be cool if the TPU pictures didn't get accidentally wiped. We've come along way lol

View attachment 321465

Hi,
What did you use ditch water

 

[KernelPanixc]

So if i understand correct. That exstender cable causing the system to crash and reset?

Yes it is OEM powersupply and when i use the extender even in bios i see voltage drops

edit: may be extender cable where too thin idk

He meant the radiator with fan zip- tied to it.

Your implementation is spot on. Especially the way it was mocked up being perfect for this thread.

Oh i get it now its from my father's car, heater was not hot enough and they buy new radiator for it.

Used some acid to clean inside (multiple times) lucky it didn't leak at the end.

 

[InVasMani]

Hi,
What did you use ditch water

Synthetic ditch water!

 

[lexluthermiester]

Hi,
What did you use ditch water

Automotive radiator fluid.

 

[Bagerklestyne]

Automotive radiator fluid.

GFuel works better for overclocks.

Side question, any got any pointers for hacking metal in a case (I've got 200mm front fans but they're not free flowing into the case due to frame support for the 120/140mm fans/radiators)

 

[taka]

GFuel works better for overclocks.

Side question, any got any pointers for hacking metal in a case (I've got 200mm front fans but they're not free flowing into the case due to frame support for the 120/140mm fans/radiators)

Angle grinder, Dremmel or metal scisor...choice is yours. Remeber to get all components out before the operation and to give a propper cleaning for metal debris.

Had the same issue with smaller fan mounts and after the airflow it's improved by a lot.

Have fun!

 

[Bagerklestyne]

Angle grinder, Dremmel or metal scisor...choice is yours. Remeber to get all components out before the operation and to give a propper cleaning for metal debris.

Had the same issue with smaller fan mounts and after the airflow it's improved by a lot.

Have fun!

Thanks taka, I'll report back with how many bandaids I needed to put on when the job is done. Chuck in a few before and after shots too (pc and fingers maybe)

 

[thesmokingman]

Thanks taka, I'll report back with how many bandaids I needed to put on when the job is done. Chuck in a few before and after shots too (pc and fingers maybe)

Dremel. One slip with an angle grinder could cut the f out of your case. Metal snippers will warp and leave cut marks all over.

 

[Carlyle2020hs]

I wanted to play around with those lightweight eDP connected displays.

The idea of a minimalistic setup was very intriguing.

This is my interpretation:

next step: Make the display see-through

 

[taka]

Thanks taka, I'll report back with how many bandaids I needed to put on when the job is done. Chuck in a few before and after shots too (pc and fingers maybe)

If you dont know or have experience with power tools maybe this metal cutter will be best for you

As long as you keep your fingers on the handles all should be good

 

[natr0n]

I wanted to play around with those lightweight eDP connected displays.

The idea of a minimalistic setup was very intriguing.

This is my interpretation:
View attachment 324297
next step: Make the display see-through

Thats a nice picture.

 

[Bagerklestyne]

If you dont know or have experience with power tools maybe this metal cutter will be best for you
View attachment 324298

As long as you keep your fingers on the handles all should be good

No no, as an aussie my level of desire to 'try something equal parts stupid and dangerous with zero experience', is very high.

I'll overthink the hell out of it before I make a single mod.

 

[nomdeplume]

Side question, any got any pointers for hacking metal in a case (I've got 200mm front fans but they're not free flowing into the case due to frame support for the 120/140mm fans/radiators)

Decent quality masking tape is your friend in most situations. This is to protect your finished edge and inwards. If your test area (first place you cut) isn't working, try another way.

Surface finish and material composition are good to understand the properties of. Low heat and slow cut still warps if you put the wrong pressure into your work area. A working understanding of the fact someone smarter than you decided that much material was required also helps, but eh. Toss up if it was them or legal.

Sometimes a gazillion RPM Dremel with a gazillion attachments is the answer. Prep, cut, sand, burnish... eff up and post the debacle here. Whatever.

No no, as an aussie my level of desire to 'try something equal parts stupid and dangerous with zero experience', is very high.

I'll overthink the hell out of it before I make a single mod.

Nah, Hard Yakka and be done with it.

 

[ShrimpBrime]

Here's my recent ghetto mod.

Edit in, that's rx 6700 xt and rx 6700 (no xt).

Molex to pcie cable mod. No fires yet!!

Timespy Extreme score

I scored 9 758 in Time Spy Extreme

Intel Core i7-13700K Processor, AMD Radeon RX 6700 XT x 2, 16384 MB, 64-bit Windows 11}

www.3dmark.com

 

[freeagent]

Here's my recent ghetto mod.

Edit in, that's rx 6700 xt and rx 6700 (no xt).

Molex to pcie cable mod. No fires yet!!

Timespy Extreme score

I scored 9 758 in Time Spy Extreme

Intel Core i7-13700K Processor, AMD Radeon RX 6700 XT x 2, 16384 MB, 64-bit Windows 11}

www.3dmark.com

That is awesome man!

 

[ThrashZone]

Hi,
No sure how ghetto it is but modifying a couple m.2 heatsinks to fit into a new laptop was fun and risky so I guess the risky part is the ghetto part but 63c max on both is very



Look closely I did add blue electrical tape on the bottom and some of the sides where stuff is really close

 

[ShrimpBrime]

That is awesome man!

Did you notice the wraith Prism on the 13700K ?? Heheheheeee

 

[freeagent]

Did you notice the wraith Prism on the 13700K ?? Heheheheeee

I sure did! That is hawt

 

[ThrashZone]

I wanted to play around with those lightweight eDP connected displays.

The idea of a minimalistic setup was very intriguing.

This is my interpretation:
View attachment 324297
next step: Make the display see-through

Hi,
That's to clean to be ghetto

 

[Carlyle2020hs]

Well i haven´t shown its backside yet

That´s K2 engine gasket silicone on a red stabilizing ruler mounted on an ikea l-bracket held on with a noctua "swivel" and elevated with gpu holder-sticks from a mining rig


And before the crypto hate starts, that´s what i bought the mining rig for:

A nice diy laptop stand capable of 3000 rpm lifting force so: "tablets beware!"

 

[Jetster]

Alright, enough internet for today

 

[A Computer Guy]

Alright, enough internet for today

View attachment 325643

Neat, a clandestine agency pc.

 

[Deleted member 229121]

So what class of laptop is that, Deep Dish or Neapolitan?

 

[A Computer Guy]

See here for custom made cardboard fan/heatsink gasket to stop thermal throttling.

Small form factor gaming - build log and support forum for new builders

I just got an ML-09B last week but I really regret not getting the more flexible sleeved cables for the SFX power supply. It's a nice case for it's size. Previously I tried some generic 4L case from ebay but the 1U PSU got wasn't modular so the cables were in the way for the side slot that I...

www.techpowerup.com

 

[Jetster]

Might need to return it