Seasonic Snow Silent 750 W Review 17

Seasonic Snow Silent 750 W Review

Efficiency, Temperatures & Noise »

Test Setup



All measurements were performed using two Chroma 6314A mainframes equipped with the following electronic loads: six 63123A [350 W each], one 63102A [100 W x2], and one 63101A [200 W]. The aforementioned equipment is able to deliver 2500 W of load, and all loads are controlled by a custom-made software. The AC source is a Chroma 6530 capable of delivering up to 3 kW of power. We also used a Rigol DS2072A oscilloscope kindly sponsored by Batronix, a Picoscope 3424 oscilloscope, a Picotech TC-08 thermocouple data logger, two Fluke multimeters (models 289 and 175), a Keithley 2015 THD 6.5 digit bench DMM, and a lab grade N4L PPA1530 3-phase power analyzer along with a Yokogawa WT210 power meter. We also included a wooden box, which, along with some heating elements, was used as a hot box. Finally, we had at our disposal three more oscilloscopes (Rigol VS5042, Stingray DS1M12, and a second Picoscope 3424), and a Class 1 Bruel & Kjaer 2250-L G4 Sound Analyzer we equipped with a type 4189 microphone that features a 16.6-140 dBA-weighted dynamic range. You will find more details about our equipment and the review methodology we follow in this article. We also conduct all of our tests at 40°C-45°C ambient to simulate the environment seen inside a typical system more accurately, with 40°C-45°C being derived from a standard ambient assumption of 23°C and 17°C-22°C being added for the typical temperature rise within a system.


We use a GPIB-USB controller to control the Chroma 6530 source, which avoids its picky Serial port. This controller was kindly provided by Prologix.

Rigol DS2072A kindly provided by:

Primary Rails Load Regulation

The following charts show the voltage values of the main rails, recorded over a range from 60 W to the maximum specified load, and the deviation (in percent) for the same load range.







5VSB Regulation

The following chart shows how the 5VSB rail deals with the load we throw at it.


Hold-up Time

Hold-up time is a very important PSU characteristic and represents the amount of time, usually measured in milliseconds, a PSU can maintain output regulations as defined by the ATX spec without input power. In other words, it is the amount of time the system can continue to run without shutting down or rebooting during a power interruption. The ATX specification sets the minimum hold-up time to 16 ms with the maximum continuous output load. In the following screenshot, the blue line is the mains signal and the yellow line is the "Power Good" signal. The latter is de-asserted to a low state when any of the +12V, 5V, or 3.3V output voltages fall below the undervoltage threshold, or after the mains power has been removed for a sufficiently long time to guarantee that the PSU cannot operate anymore.



This unit's hold-up time was much higher than the minimum the ATX sets.

Inrush Current

Inrush current or switch-on surge refers to the maximum instantaneous input-current drawn by an electrical device when it is first turned on. Because of the charging current of the APFC capacitor(s), PSUs produce large inrush current right as they are turned on. Large inrush current can cause the tripping of circuit breakers and fuses and may also damage switches, relays, and bridge rectifiers; as a result, the lower a PSU's inrush current right as it is turned on, the better.



As you can see in the graph above, inrush current was high; however, it never reached dangerously high levels.

Load Regulation and Efficiency Measurements

The first set of tests revealed the stability of the voltage rails and the Snow Silent-750's efficiency. The applied load was equal to (approximately) 10%-110% of the maximum load the PSU can handle, in 10% steps.

We conducted two additional tests. In the first test, we stressed the two minor rails (5V and 3.3V) with a high load while the load at +12V was only 0.10 A. This test reveals whether the PSU is Haswell ready or not. In the second test, we dialed the maximum load the +12V rail could handle while the load on the minor rails was minimal.

Load Regulation & Efficiency Testing Data - Seasonic Snow Silent-750
Test12 V5 V3.3 V5VSBPower
(DC/AC)
EfficiencyFan SpeedFan NoiseTemp
(In/Out)
PF/AC
Volts
10% Load4.379A1.984A1.969A0.975A74.71W88.66%0 RPM0 dBA 45.34°C0.800
12.140V5.035V3.349V5.105V84.27W 41.25°C230.1V
20% Load9.795A2.973A2.954A1.175A149.69W91.10%534 RPM27.8 dBA 39.89°C0.903
12.135V5.033V3.349V5.094V164.31W 43.67°C230.1V
30% Load15.561A3.476A3.464A1.375A224.82W93.06%534 RPM27.8 dBA 40.14°C0.941
12.130V5.031V3.348V5.081V241.59W 44.08°C230.0V
40% Load21.320A3.973A3.942A1.575A299.68W93.38%585 RPM28.5 dBA 40.59°C0.959
12.126V5.030V3.347V5.069V320.93W 44.67°C230.1V
50% Load26.745A4.970A4.930A1.776A374.64W93.51%950 RPM34.8 dBA 41.94°C0.969
12.121V5.029V3.346V5.057V400.66W 46.35°C230.0V
60% Load32.170A5.963A5.917A1.980A449.51W93.20%1250 RPM42.3 dBA 42.10°C0.976
12.117V5.028V3.345V5.044V482.32W 46.94°C230.1V
70% Load37.605A6.968A6.905A2.184A524.58W92.97%1730 RPM45.8 dBA 43.31°C0.979
12.113V5.026V3.344V5.033V564.26W 48.56°C230.1V
80% Load43.039A7.960A7.895A2.390A599.47W92.61%2040 RPM50.5 dBA 43.75°C0.981
12.109V5.024V3.344V5.019V647.30W 49.45°C230.1V
90% Load48.906A8.465A8.404A2.393A674.52W92.38%2130 RPM52.4 dBA 44.61°C0.984
12.104V5.023V3.343V5.010V730.15W 50.79°C230.0V
100% Load54.521A8.963A8.886A3.005A749.38W91.86%2130 RPM52.4 dBA 44.90°C0.985
12.100V5.022V3.342V4.990V815.75W 51.56°C230.2V
110% Load60.735A8.965A8.889A3.008A824.29W91.57%2130 RPM52.4 dBA 45.00°C0.985
12.095V5.020V3.341V4.982V900.20W 52.29°C230.1V
Crossload 10.098A15.015A15.005A0.004A126.98W85.84%1125 RPM37.3 dBA 43.56°C0.890
12.139V5.027V3.351V5.103V147.93W 48.21°C230.1V
Crossload 261.945A1.002A1.003A1.001A762.51W92.55%2130 RPM52.4 dBA 44.06°C0.985
12.094V5.024V3.343V5.047V823.90W 50.28°C230.1V
The Snow Silent-750's load regulation was very tight on all but the 5VSB rail, and the unit easily delivered its full power over a prolonged period of time at 45°C. At up to the 40% load test, the fan also spun at very slowly, which had it produce very little noise. The fan became audible at 70% load and cracked 52 dBA afterward, which is loud enough.
Next Page »Efficiency, Temperatures & Noise
View as single page
Dec 23rd, 2024 00:38 EST change timezone

New Forum Posts

Popular Reviews

Controversial News Posts