Test Setup

All measurements were performed using two Chroma 6314A mainframes equipped with the following electronic loads: six 63123A [350 W each], one 63102A [100 W x2], and one 63101A [200 W]. The aforementioned equipment is able to deliver 2500 W of load, and all loads are controlled by a custom-made software. The AC source is a Chroma 6530 capable of delivering up to 3 kW of power. We also used a Rigol DS2072A oscilloscope kindly sponsored by Batronix, a Picoscope 3424 oscilloscope, a Picotech TC-08 thermocouple data logger, two Fluke multimeters (models 289 and 175), a Keithley 2015 THD 6.5 digit bench DMM, and a Yokogawa WT210 power meter. We also included a wooden box, which, along with some heating elements, was used as a hot box. Finally, we had at our disposal three more oscilloscopes (Rigol VS5042, Stingray DS1M12, and a second Picoscope 3424), and a Class 1 Bruel & kjaer 2250-L G4 Sound Analyzer we equipped with a type 4189 microphone that features a 16.6-140 dBA-weighted dynamic range. You will find more details about our equipment and the review methodology we follow in this article. We also conduct all of our tests at 40°C-45°C ambient to simulate the environment seen inside a typical system more accurately, with 40°C-45°C being derived from a standard ambient assumption of 23°C and 17°C-22°C being added for the typical temperature rise within a system.

We use a GPIB-USB controller to control the Chroma 6530 source, in order to avoid its very picky serial port. This controller was kindly sponsored by Prologix.

Primary Rails Load Regulation

The following charts show the voltage values of the main rails, recorded over a range from 60 W to the maximum specified load, and the deviation (in percent) for the same load range.

5VSB Regulation

The following chart shows how the 5VSB rail deals with loads we throw at it.

Hold-up Time

Hold-up time is a very important PSU characteristic and represents the amount of time, usually measured in milliseconds, a PSU can maintain output regulations as defined by the ATX specification without input power. In other words, it is the amount of time the system can continue to run without shutting down or rebooting during a power interruption. The ATX specification sets the minimum hold-up time to 16 ms with the maximum continuous output load. In the following screenshot, the blue line is the mains signal and the yellow line is the "Power Good" signal. The latter is de-asserted to a low state when any of the +12V, 5V, or 3.3V output voltages fall below the undervoltage threshold, or after the mains power has been removed for a sufficiently long time to guarantee that the PSU cannot operate anymore.



The P1700-MA's hold-up time was way too low! The PSU registered an incredible failure in this test, which will cost the unit many performance points. LEPA should definitely use much larger bulk caps.

Inrush Current

Inrush current or switch-on surge refers to the maximum, instantaneous input-current drawn by an electrical device when it is first turned on. Because of the charging current of the APFC capacitor(s), PSUs produce large inrush-current right as they are turned on. Large inrush current can cause the tripping of circuit breakers and fuses and may also damage switches, relays, and bridge rectifiers; as a result, the lower a PSU's inrush current right as it is turned on, the better.



Inrush current was below 50 A, so there are no problem here. However, given the low combined capacity of the bulk caps, we expected inrush current to be even lower.

Load Regulation and Efficiency Measurements

The first set of tests revealed the stability of the voltage rails and the P1700-MA-EU's efficiency. The applied load was equal to (approximately) 10%-106% of the maximum load the PSU can handle, in 10% steps.

We conducted two additional tests. In the first test, we stressed the two minor rails (5V and 3.3V) with a high load while the load at +12V was only 0.10 A. This test reveals whether the PSU is Haswell ready or not. In the second test, we dialed the maximum load the +12V rail could handle while the load on the minor rails was minimal.

Load regulation at +12V was very loose for our tastes, which is a common problem in PSUs that are based on this specific Enermax platform. The minor rails' load regulation definitely wasn't top-notch, but they performed noticeably better than +12V. Enermax had to compromise on load regulation with this design to offer the highest possible efficiency, a compromise Enermax wouldn't have had to make with a modern platform running such a high capacity.

Although its official specifications speak of 40°C as the maximum temperature at which it can deliver its capacity, our sample delivered its peak power at up to 48°C. However, we don't recommended pushing it outside of its official specifications since you can't blame the manufacturer should the unit fail; nor would the warranty cover such a failure. Adda's ball-bearing fan was loud with low loads and very loud with high loads.