Rosewill Tachyon 1000 W Review 8

Rosewill Tachyon 1000 W Review

Efficiency, Temperatures & Noise »

Test Setup

All measurements were performed using two Chroma 6314A mainframes equipped with the following electronic loads: six 63123A [350 W each], one 63102A [100 W x2], and one 63101A [200 W]. The aforementioned equipment is able to deliver 2500 W of load, and all loads are controlled by a custom-made software. We also used a Picoscope 3424 oscilloscope, a Picotech TC-08 thermocouple data logger, a Fluke 175 multimeter, and a Yokogawa WT210 power meter. We also included a wooden box, which, along with some heating elements, was used as a hot box. Finally, we had at our disposal four more oscilloscopes (Rigol 1052E and VS5042, Stingray DS1M12, a second Picoscope 3424), and a CEM DT-8852 sound level meter. In this article, you will find more details about our equipment and the review methodology we follow. Finally, we conduct all of our tests at 40 - 45°C ambient in order to simulate with higher accuracy the environment seen inside a typical system, with 40 - 45°C being derived from a standard ambient assumption of 23°C and 17 - 22°C being added for the typical temperature rise within a system.

Primary Rails Voltage Regulation

The following charts show the voltage values of the main rails, recorded over a range from 60W to the maximum specified load, and the deviation (in percent) for the same load range.







5VSB Regulation

The following chart shows how the 5VSB rail deals with the load we throw at it.


Hold-up Time

The hold-up time is a very important characteristic of a PSU and represents the amount of time, usually measured in milliseconds, that a PSU can maintain output regulations as defined by the ATX spec without input power. In other words, it is the amount of time that the system can continue to run without shutting down or rebooting during a power interruption. The ATX spec sets the minimum hold-up time to 16 ms at maximum continuous output load. In the following screenshot, the blue line is the mains signal and the yellow line is the "Power Good" signal. The latter is de-asserted to a low state when any of the +12V, 5V, or 3.3V output voltages fall below the undervoltage threshold, or after the mains power has been removed for a sufficiently long time to guarantee that the PSU cannot operate anymore.



Although the hold-up caps are of significant capacity, the effective hold-up time is much lower than the minimum allowed.

Inrush Current

Inrush current or switch-on surge refers to the maximum, instantaneous input-current drawn by an electrical device when first turned on. Because of the charging current of the APFC capacitor(s), PSUs produce large inrush-current right as they are turned on. Large inrush current can cause the tripping of circuit breakers and fuses and may also damage switches or relays; as a result, the lower the inrush current of a PSU right as they are turned on, the better.



Thanks to its large APFC caps, the inrush current that the Tachyon 1000 W registers is high and close to the reading of the monstrous Silverstone ZM1350 and Enermax EMR1500GT units.

Voltage Regulation and Efficiency Measurements

The first set of tests revealed the stability of the voltage rails and the efficiency of the Tachyon-1000. The applied load was equal to (approximately) 20%, 40%, 50%, 60%, 80%, 100% and 110% of the maximum load that the PSU can handle. In addition, we conducted two more tests. In the first test, we stressed the two minor rails (5V and 3.3V) with a high load while the load at +12V was only 2 A, and, in the second test, we dialed the maximum load that the +12V rail could handle while the load on the minor rails was minimal.

Voltage Regulation & Efficiency Testing Data
Rosewill Tachyon 1000W
Test12 V5 V3.3 V5VSBPower
(DC/AC)
EfficiencyFan SpeedTemp
(In/Out)
PF/AC
Volts
20% Load14.581A1.929A1.949A0.976A199.76W91.54%834 RPM 38.92°C0.946
12.221V5.178V3.381V5.112V218.22W 45.67°C230.1V
40% Load29.566A3.869A3.919A1.175A399.62W93.09%834 RPM 39.78°C0.970
12.193V5.155V3.365V5.098V429.30W 48.10°C230.0V
50% Load36.959A4.857A4.912A1.570A499.59W93.13%834 RPM 40.94°C0.975
12.179V5.144V3.358V5.087V536.47W 50.05°C229.9V
60% Load44.372A5.838A5.907A1.970A599.54W92.95%834 RPM 42.40°C0.977
12.165V5.132V3.351V5.074V645.00W 53.53°C229.8V
80% Load59.412A7.827A7.914A2.369A799.38W92.18%1680 RPM 44.41°C0.979
12.136V5.108V3.335V5.058V867.20W 54.44°C229.8V
100% Load75.335A8.833A8.938A2.475A999.22W91.39%1680 RPM 45.47°C0.982
12.107V5.090V3.322V5.046V1093.35W 58.25°C229.7V
110% Load83.697A8.844A8.952A2.478A1099.12W90.97%1680 RPM 45.98°C0.983
12.091V5.084V3.316V5.040V1208.25W 60.78°C229.6V
Crossload 11.963A12.000A12.005A0.502A128.40W87.00%1680 RPM 43.30°C0.727
12.229V5.122V3.362V5.112V147.59W 49.90°C230.2V
Crossload 282.933A1.000A1.003A1.003A1017.32W91.73%1680 RPM 45.83°C0.982
12.103V5.135V3.342V5.079V1109.10W 57.90°C229.7V

Efficiency is very high throughout all load levels and the PSU did, on top of that, prove that it can easily deliver 110% of its maximum rated capacity at 46°C ambient. Also, voltage regulation on all rails was good, especially at +12V, given it registered a deviation very close to 1%. We noticed something pretty strange in the fan's operation during the 80% load test. Instead of a linear and smooth RPM increase, the fan throttled up into full speed instantly. This was unexpected and the fan should increase its speed linearly and not in such a peculiar way since it resulted in a sudden rise of noise output.
Next Page »Efficiency, Temperatures & Noise
View as single page
Dec 23rd, 2024 01:54 EST change timezone

New Forum Posts

Popular Reviews

Controversial News Posts