GIGABYTE introduced the GeForce RTX 4070 Ti SUPER WindForce MAX graphics card. It is characterized by an oversized air cooling solution that gives it some large dimensions of 33.1 cm length, 5.55 cm thickness (3 slots), but more importantly, a height of 13.6 cm, which could pose a challenge for those with mid-tower cases, given the tight cable bending restrictions of the 12VHPWR connector. GIGABYTE found a novel solution to this problem. The power connector is located pointing toward the tail end of the card, where the PCB terminates. The PCB is only two-thirds the length of the card, and so the power cable can be routed in without any bends.

The WindForce cooling solution features a trio of 100 mm fans that ventilate a large aluminium fin-stack heatsink with nine copper heatpipes, and a direct-touch base. GIGABYTE has given the card a factory overclock of 2655 MHz GPU clocks, compared to 2610 MHz reference, while leaving the memory untouched at 21 Gbps. The card offers dual-BIOS, with the default BIOS enabling these clock speeds, and the Silent BIOS lowering them to reference speeds, while quietening the cooler. Based on the 5 nm AD103 silicon, the RTX 4070 Ti SUPER is endowed with 8,448 CUDA cores, 66 RT cores, 264 Tensor cores, 96 ROPs, and 264 TMUs. The GPU gets 16 GB of 21 Gbps GDDR6X memory across a 256-bit wide memory interface. The company didn't reveal pricing.

ASUS launched the Prime Series of GeForce RTX 40-series "Ada" graphics cards that meet NVIDIA's new SFF-Ready specification that sets 304 mm x 151 mm x 50 mm (length x height x thickness) as the maximum dimensions for a graphics card to qualify. What's interesting, is that NVIDIA intended for the SFF-Ready standard to apply to performance-segment and enthusiast-class GPUs (RTX 4070 SUPER and up), however, ASUS has designed the Prime series for the RTX 4060 Ti, RTX 4070, and RTX 4070 SUPER; there are no cards in the series based on the RTX 4070 Ti SUPER or the RTX 4080 SUPER, yet.

ASUS is using a common board design for its RTX 4070 SUPER, RTX 4070, and RTX 4060 Ti Prime series graphics cards, which measures 269 mm x 120 mm x 50 mm, while the heatsink and PCB underneath the cooler shroud may vary between the RTX 4070/SUPER and the RTX 4060 Ti cards. The cooler uses a trio of 70 mm fans to ventilate an aluminium fin-stack heatsink, much of the airflow from the third fan goes through the heatsink and back out from a large cutout in the backplate. The RTX 4070 and RTX 4060 Ti cards use single 8-pin PCIe power inputs, while the RTX 4070 SUPER uses a 16-pin 12VHPWR input. There are a total of six SKUs, two per GPU, one of which sticks to the NVIDIA reference clock speeds, and the other being an OC SKU with a minor factory overclock.

Lian Li was also keen to show us its unique EDGE PSU series which features a dual-chamber chassis with L-shaped design that allow easier and more direct access for cable connection. The Lian Li EDGE PSU series will be available in 850 W, 1,000 W, and 1,300 W power output versions, with a special EG850 Mesh version with removable fan grill that allows easier cleaning. In addition to all the usual connectors, the Lian Li EDGE PSU lineup also comes with a built-In USB2.0 Hub.

The entire Lian Li EDGE PSU series is rated at 80 Plus Platinum efficiency, except for the EG850 Mesh which is 80 Plus Gold certified and should be the first one available. Bear in mind that the EG850 Mesh has slightly different specifications, but we'll confirm these as it becomes available or comes to our review testbed. The entire series is fully modular with sleeved cables and cable combs. Lian Li is using a new 12VHPWR connector design with more durable contact points for each pin, as well as high-quality electrolytic capacitors. In case you are wondering, the precise dimensions are 182x86x150 mm and as showcased at the event, Lian Li will have both black and white color options for some models.

Akasa brought an interesting set of new gear from its diverse portfolio of PC hardware to Computex 2024. The star attraction is the elegant Hawking series fanless case. The silver-aluminium variant is a work of art. The Hawking series is designed for ASUS NUC motherboards with 28-35 W Core i3 chips. It features a solid copper baseplate to pull heat from the SoC, with a series of heat pipes pushing it to the body, which doubles up as an extruded aluminium heatsink. Akasa also showcased several smaller fanless cases under the Maze and Gem series, for Raspberry Pi 4.

Next up, Akasa showed us a couple of slick aluminium portable SSD enclosures that feature 40 Gbps USB4 connectivity. You simply install an M.2-2280 SSD, a bridge chip has a PCIe Gen 3 x4 connection for this drive on one end, and the 40 Gbps USB4 interface on the other. A single type-C cable is used for both power and host connectivity. Among the various connectivity accessories showcased was a 5 Gbps Ethernet NIC with CAT-6a, based on a Realtek controller.

CE LINK LIMITED ("CE-LINK"), a leading manufacturer of consumer electronics, is thrilled to announce the launch of its revolutionary SFX power supply, setting new benchmarks in both performance and compactness. Engineered to elevate gaming and IT experiences, this latest innovation from CE-LINK stands as the most compact SFX power supply in its category, delivering an impressive maximum output of 1000 W. From April 11-14, visit booth 3A-02 in Hall 3 of the AsiaWorld-Expo to experience this game-changer at the upcoming Global Sources Electronic Show in Hong Kong.

This product features exceptional compactness and outstanding performance. With its small size, measuring just 125x100x63.5 mm, this SFX power supply offers a powerful output, delivering up to 1000 W of maximum power. It is designed to fit seamlessly into any setup, whether it be an ATX or ITX gaming chassis. Additionally, versions with 850 W and 750 W capacities are available to meet various power requirements.

Graphics card enthusiasts with a thing for earthy green hues, will likely appreciate Manli's latest products—its Gallardo graphics card range has expanded with two new models. The Asian and European market-focused manufacturer has already unleashed "refreshed" models that utilize NVIDIA's GeForce RTX 40-series SUPER GPUs, but the newest entries sport a revised signature green flagship "Gallardo" design. VideoCardz has pored over the small details—it turns out that Manli has produced a slimmer profile: "perhaps something that is not obvious is that Manli has introduced the RTX 4070 Ti SUPER Gallardo already. The new version marks a second revision, featuring an entirely different aesthetic compared to its predecessor. The most important change is that it no longer occupies a 3.5-slot space." Manli has evidently put together a "much slimmer 2-slot version" under a "M3604+N693" moniker.

The non-Ti model is likely coming out soon, but Manli has not yet announced official pricing or launch date details for their newly redesigned Gallardo Ada Lovelace cards—official product pages were created last week. Despite flagship status, VideoCardz notes that Manli has not implemented any factory overclocking—the Gallardo range is often associated with: "system integrators like Sycom for further customization." The spec sheet advertises integrated LED lighting with seven available color cycles, four 6 mm copper heat pipes with segmented heatsinks, and a metal backplate for reinforcement and protective purposes.

Online hardware communities continue to discuss the 12VHPWR connection standard's troubled existence, while revised technology gets worked on—quietly—in the background. PCI-SIG's 12V-2x6 connector was first revealed last summer, signalling an alternative power delivery method for high-wattage graphics cards. Past TPU reports show that the 12V-2x6 16-pin design has already popped up on select NVIDIA Founders Edition cards, GeForce RTX 40 SUPER custom graphics card designs, and various new generation power supplies. Earlier today, Алексей (AKA wxnod) took to social media and posted an image of the freshly deshrouded "H++" 12V-2x6 (total design limit: 675 W) socket, as well as a shot of the familiar "H+" 12VHPWR (max. 600 W).

This fifth generation socket design largely rolled out with Team Green's GeForce RTX-40 SUPER card series, although wxnod notes that exceptions do exist: "Some AIC GeForce RTX 4070 SUPER, 4070 Ti SUPER and 4080 SUPER cards are still using the H+12VHPWR interface." The H++ identified 12V-2x6 design's power limit peaks at 675 W—a technical breakdown from last July revealed that 75 W comes from the expansion slot, while the big 600 W portion flows through the 16-pin connector. As mentioned before, 12V-2x6 debuted on a few Non-SUPER cards back in 2023, but last month's SUPER series product launch marked a more comprehensive rollout. AMD has indicated that it is considering an adoption of Gen 5 H++ in the future, but we have not heard much on that subject since last August. A new generation 16-pin PCIe 6.0 power connector design was linked to the upcoming NVIDIA RTX 50-series of "Blackwell" GPUs, but Hardware Busters has refuted rumors generated by Moore's Law is Dead. Team Green is expected to remain faithful to "H++" 12V-2x6 with the launch of next generation graphics cards.

LIAN LI Industrial Co. Ltd., a leading chassis and PC accessories manufacturer, premieres the LIAN LI 2024 DIGITAL EXPO at 9 am EST on YouTube. In this 2-part video, LIAN LI shares updates on prototype cases, a standing desk, and unveils new concepts for an all-in-one cooler and power supply. The prototypes include the SUP-01, the case that experiments with a front GPU layout, the DAN Cases A3 M-ATX case, and the O11 VISION BACK CONNECT. LIAN LI also unveils the GALAHAD II LCD SHIFT, an AIO that minimizes the tubing, the EDGE Series PSU, a new form factor power supply that solves cable access in dual chamber cases, and the DK-07, a new standing desk with new features. The LIAN LI 2024 DIGITAL EXPO will be followed by a roundtable discussion hosted by Jameson Chen, CEO at LIAN LI, with YouTube influencers Stuart Tonks from GGF Events, Justin Robey from Robytech, and PCMR's founder Pedro Valadas.

The SUP-01, a compact 45-liter case, reimagines the PC layout with a front-positioned graphics card and innovative cooling. Equipped with airflow-optimized mesh panels, it surpasses the LANCOOL 216 in cooling performance. The GPU's unique placement optimizes cooling without sacrificing aesthetics and is supported by adjustable brackets. The airflow configuration strategically utilizes GPU fans and rear fans as intakes, and right-side fans as exhausts, ensuring optimal GPU and CPU cooling. The main chamber accommodates motherboard sizes up to ATX, pre-mounted PCIe 4.0 riser cable, and features clearance for 280 to 360 mm AIOs. Storage options include two SSDs or 3.5" HDDs, a removable drive cage, and magnetic dust filters to maintain system cleanliness. The price is set to be $149.99.

CableMod issued a statement—just before the last Christmas holiday—detailing a safety recall of 16-pin 12VHPWR angled adapters, version 1.0 and 1.1. This announcement received widespread media coverage (at least in tech circles), but some unfortunate customers have not yet received the memo about faulty adapters—CableMod's 90° angled and 180° hard connectors can overheat and in worst case scenarios, actually melt. HotHardware, amusingly named given this context, was the first hardware news outlet to notice that the Consumer Product Safety Commission (CPSC) had published a "GPU Angled Adapter" recall notice to its website earlier today, under "Recall number 24-112."

The US government body's listing outlines aforementioned hazardous conditions, along with an estimated 25,300 affected unit count. The CPSC's recommended "Remedy" advice is as follows: "Consumers should immediately stop using the recalled angled adapters and contact CableMod for instructions on how to safely remove their adapter from the GPU and for a full refund, including cost of shipping, or a $60 store credit for non-customized products, with free standard shipping. Consumers will be asked to destroy the adapter and upload a photo of the destroyed product to cablemod.com/adapterrecall/. The instructions on how to safely remove the adapter are also located on that site. Once destroyed, consumers should discard the adapter in accordance with local laws." The Safety Commission has gathered some customer feedback intelligence on this matter: "The firm (CableMod Ltd., of China) has received 272 reports of the adapters becoming loose, overheating and melting into the GPU, with at least $74,500 in property damage claims in the United States. No injuries have been reported."

Palit has kind of gone against the 12VHPWR grain with its GeForce RTX 4080 Super GamingPro OC graphics card—PC SIG's 16-pin power connector is the default standard for the NVIDIA GeForce RTX 40 series, but an outbreak of technical snafus has caused many to question the format's future. A new 12V-2x6 connection standard is touted as 12VHPWR's natural successor, but PC parts manufacturers continue to produce products that utilize the latter. HXL discovered a MaxSun custom GeForce RTX 4070 SUPER design that sported two completely bog standard 8-pin PCIe power connectors (in lieu of 12VHPWR), but a follow up report indicates that the Chinese board partner has scrubbed the offending item from its web presences.

Jisakuhibi Japan's review of the Palit GeForce RTX 4080 Super GamingPro OC model included close-up shots of the card's PCB—the publication's social media account noted an intriguing yet empty section: "(Palit's) board seems to be able to natively set the auxiliary power supply to PCIe 8-pin x 2 instead of 12VHPWR." The unoccupied area sits just south-east of the standard 12VHPWR connector—the provisional positioning of pin holes suggests that Palit's PCB could be designed for a separate professional graphics card solution. The company is unlikely to divulge its original intent with the placement of older auxiliary power connectors—ultimately 12VHPWR is the way forward.

PC power supply manufacturer Seasonic has introduced a new limited-edition variant of its Vertex 1000 W 80+ Gold certified modular power supply featuring an eye-catching design inspired by cherry blossoms. Dubbed the "Vertex Sakura," this specially-themed PSU sports a clean white color scheme with pink Sakura flower graphics and a unique textured paint finish. The Vertex Sakura caters specifically to PC enthusiasts and case modders in Japan who want to build a themed rig coordinated around the colors and aesthetic of traditional Japanese cherry blossoms. It offers the same fully modular cabling as the standard Vertex 1000 W model, allowing builders flexibility in cable management.

The PSU also meets the latest ATX 3.0 specifications, including a 12VHPWR connector to support next-generation high-wattage GPUs. Seasonic showcased the Vertex Sakura 1000 W unit at 30,000 yen (around $200 USD) in Japan, where retailers recommend interested buyers preorder as soon as possible due to limited availability. Specific regional launch details outside of Japan are still forthcoming. But the Vertex Sakura's blend of technical prowess and stunning cherry blossom visual flair will likely attract global attention from PC builders looking to add an extra touch of style to their high-end systems.

NVIDIA today launched the third and final high-end GPU in its GeForce RTX 40-series SUPER refresh. The new GeForce RTX 4080 SUPER is being launched at an attractive $999 price, compared to the $1,199 that the RTX 4080 originally launched at. Besides this huge 20% cut in pricing, there's also more performance on offer, as the company chose to max out the 5 nm AD103 silicon that it's based on. If you recall, the RTX 4080 has 76 out of 80 streaming multiprocessors of the AD103 enabled, and its memory runs at an odd 22.4 Gbps speed. The RTX 4080 SUPER gets all 80 SM, and a well rounded 23 Gbps memory speed.

With 80 SM on tap, you get 10,240 CUDA cores, 320 Tensor cores, 80 RT cores, 320 TMUs, and 112 ROPs. The memory size is unchanged at 16 GB, across the 256-bit wide memory interface of the AD103; as is the total graphics power (TGP), at 320 W. All cards will include an NVIDIA-designed adapter that converts three 8-pin PCIe power connectors into a 12VHPWR that's capable of delivering 450 W of power. The target audience for this card is the same as that of the RTX 4080—maxed out 4K Ultra HD gaming with ray tracing. At $999, the RTX 4080 SUPER allows NVIDIA to better compete with the AMD Radeon RX 7900 XTX that's sometimes spotted for prices as low as $900. Don't forget to catch our exhaustive review coverage from the links below!

NVIDIA GeForce RTX 4080 SUPER Founders Edition | ASUS ROG Strix RTX 4080 SUPER OC | ASUS TUF Gaming RTX 4080 SUPER OC | MSI RTX 4080 SUPER Expert | Gigabyte RTX 4080 SUPER Gaming OC | PNY RTX 4080 SUPER Verto | Galax RTX 4080 SUPER SG 1-click OC | Palit RTX 4080 SUPER GamingPro OC | Zotac RTX 4080 SUPER AMP Extreme AIRO

Leading power supply manufacturer FSP Group proudly announces its PSU lineup now features native 12VHPWR connectors, fully prepared to harness the power of NVIDIA's RTX 4080 SUPER, RTX 4070 Ti SUPER, and RTX 4070 SUPER graphics cards. For a truly supercharged experience, FSP PSUs go beyond compatibility. They're fully compliant with both ATX 3.0 and PCIe 5.0 regulations, boasting support for 2x total power excursion and 3x GPU power excursion. This ensures unleashing the full potential of these new GPUs without breaking a sweat.

Explore the FSP ATX 3.0 & PCIe 5.0 PSU range, starting from 750 W, and find the perfect match for your RTX 40 SUPER Series.

Leading power supply manufacturer FSP Group proudly announces its PSU lineup now features native 12VHPWR connectors, fully prepared to harness the power of NVIDIA's RTX 4080 SUPER, RTX 4070 Ti SUPER, and RTX 4070 SUPER graphics cards. For a truly supercharged experience, FSP PSUs go beyond compatibility. They're fully compliant with both ATX 3.0 and PCIe 5.0 regulations, boasting support for 2x total power excursion and 3x GPU power excursion. This ensures unleashing the full potential of these new GPUs without breaking a sweat. Explore the FSP ATX 3.0 & PCIe 5.0 PSU range, starting from 750 W, and find the perfect match for your RTX 40 SUPER Series.

Cooler Master, a leading innovator in PC Hardware, today announced the V Platinum V2 power supply unit (PSU). Designed to cater to high-power applications in fields like machine learning, AI and advanced workstations, the V Platinum V2 sets a new benchmark in PSU performance. Available in three powerful variants - 1100 W, 1300 W and 1600 W - this PSU is not just a powerhouse for the latest gaming needs but a cornerstone for the most demanding computational tasks.

"Cooler Master is committed to pushing the frontiers of technology, and the V Platinum V2 is a testament to this pursuit," said Jimmy Sha, Cooler Master CEO. "By integrating noise reduction and thermal management features, we've created a PSU that's not only incredibly efficient but supremely quiet, making it an ideal choice for professionals and enthusiasts seeking the utmost in performance."

MAXSUN is an NVIDIA board partner focused on the Chinese domestic market. The company "innovated" a custom design GeForce RTX 4070 SUPER graphics card that breaks convention of a 12VHPWR power connector, and provides two regular 8-pin PCIe power connectors to draw power from. Although it's quite common to see custom RTX 4070 cards with single 8-pin PCIe power connectors due to its 200 W TGP, with the new RTX 4070 SUPER, NVIDIA increased the power limits, with the TGP now set at 220 W, which meant that nearly every board partner has had to implement the 12VHPWR connector, and include an NVIDIA designed adapter that converts two 8-pin PCIe to a 12VHPWR that's capable of 300 W continuous power delivery.

The MAXSUN card features an 8-pin native PCB design, it directly has the 8-pin connectors on the card, so there's no adapter included. China is a vastly compatibility-conscious market, and so such design choice go a long way to appeal to buyers. The presence of 8-pin PCIe connectors should particularly benefit case compatibility, where the connectors can tolerate much tighter cable bends than 12VHPWR, including with the NVIDIA-designed adapter.

Corsair Gaming, Inc., a leading global provider and innovator of high-performance gear for gamers, streamers, content-creators, and gaming PC builders, today announces full support for NVIDIA's RTX 4080 Super, RTX 4070 Ti Super, and RTX 4070 Super graphics cards with its latest power supply ranges. These new GPUs offer impressive performance boosts, particularly when using AI-powered DLSS 3.0, making it a great time for enthusiasts to build a new gaming PC or upgrade their current system. Corsair recommends the , SF850L, and HX1000i PSUs for users looking to integrate these new cards into their builds, as they provide the necessary power, even for the top RTX 4080 Super, and include a compatible PCIe 5.0 12VHPWR GPU power cable for trouble-free operation.

In addition to its PSUs, Corsair offers a range of world-class hardware ideal for PC builds featuring these new graphics cards - from its extensive lineup of cases and fans to Dominator Titanium DDR5 DRAM and iCUE LINK water cooling solutions. Corsair will also shortly be offering fully assembled high-performance Vengeance gaming PCs and custom-built ORIGIN PCs with NVIDIA's full range of RTX 4000-series Super graphics cards.

YEYIAN at the 2024 International CES displayed some really wacky cooling and power solutions. Over in the cooling front, was got to see a super rare 480 mm AIO. This cooler has a 480 mm x 120 mm radiator, which requires four 120 mm in a row. We're not sure if there are any cases that support this radiator size, but we're sure it could become a thing. It would be interesting to compare the cooling performance of a 480 mm x 120 mm AIO with that of a 420 mm x 140 mm (a much more popular form-factor). YEYIAN's AIO coolers come in three sizes—360 mm x 120 mm, 480 mm x 120 mm, and 420 mm x 140 mm. The pump-blocks feature a 2.1-inch IPS LCD display with 480 x 480 pixels resolution, which can be programmed to display anything. Each of the included fans turn at speeds of up to 2600 RPM, pushing up to 72 CFM of airflow, with as high as 23 dBA noise.

Next up, YEYIAN showed off its Orion series full modular ATX 3.1 power supplies. These meet the latest ATX 3.1 and PCIe Gen 5 spec; and offer a native 12V-2x6 power connector, the successor to 12VHPWR with more mechanical durability, which can deliver 600 W of continuous power. The YEYIAN Orion series comes in 850 W, 1300 W, and 1600 W capacities, with the 1300 W and 1600 W models meeting 80 Plus Platinum efficiency; while the 850 W model meets 80 Plus Gold. All three are equipped with a 600 W-capable 12V-2x6; the top 1600 W offers two of these in case you have one of those crazy GALAX HOF RTX 4090 cards.

ENERMAX has showcased its new power supply lineup at the CES 2024 show in Las Vegas, including the new PlatiGemini and REVOLUTION D.F. 12 PSU series. The new PlatiGemini series is certified with Intel ATX 3.1 and ATX12VO compliance and features 80 Plus Platinum efficiency. What makes it special is the fact that it comes with both 24-pin ATX and 10-pin 12VO connectors, ensuring support for both current and future updates as well as bridging the gap between specifications. The ENERMAX PlatiGemini is a full modular PSU that comes will initially be available with 1200 W power output, uses 135 mm dual-ball bearing fan with patented Dust-free Rotation (D.F.R.) function, and comes with individually sleeved cables.

In addition to the new PlatiGemini PSU series, ENERMAX new REVOLUTION D.F 12 series which has been announced at CES 2024 show is one of the smallest ATX 3.1 power supply units on the market, where the 750 W version measures just 122 mm in depth. This means that it can also be installed in a Mini-ITX case without an additional SFX to ATX mounting bracket. As said, the REVOLUTION D.F 12 series meets Intel's ATX 3.1 standard, has 80 Plus Gold efficiency, and comes with native 600 W 12VHPWR connector. It uses a 115 mm dual-ball bearing fan with the same Dust-free Rotation (D.F.R.) function, features a silent mode where the fan is switched off below 50 percent power load.

The theme at be quiet! this CES is all about RGB lighting and white color variants. This is a big aesthetic departure from be quiet! which tends to have understated, mostly black product styling, with minimal use of RGB. Ah well, as long as it's all quiet. Among the cases, we saw all-white editions of the Dark Base 701, and Dark Base Pro 901 cases. The Dark Base 701 white retains its essential design and functionality, but now gets two addressable RGB silicone diffusers along the sides of the front panel. The interiors are all white, as are the included fans. The Dark Base Pro 901 white lacks any such RGB lighting elements, it's more of just a whitewash.

As we said, be quiet! is betting big on RGB and white color scheme this year, and has unveiled white variants of its Silent Wings 4, Light Wings, and Pure Wings 3 fan series, across all available sizes. These see white take over the frames and impellers. be quiet! collaborated with SignalRGB, the experts in elaborate RGB lighting, to create an art piece—a wall of 192 Light Wings White fans, all controlled through a single machine. The fans work like a mosaic to create actual images when viewed from a distance. Very creative!

A refreshing change with Thermaltake's power supply exhibition this CES was that it brought out all its mid-range capacities ranging between 750 W to 1000 W. This is the only narrow band in which you can expect 12VHPWR or 12V-2x6 connectors that are rated for 450 W or above, which is needed if you plan on GPUs such as the RTX 4080 SUPER or above. The new Toughpower SFX Platinum series comes in the traditional SFX form-factor, and in high wattage models such as 750 W, 850 W, and 1000 W. It fully meets the latest ATX 3.1 specification, and comes with a native 12V-2x6 connector (a more mechanically sound 12VHPWR successor). The Toughpower SFX has broadly two variants, Gold and Platinum, aligning with their respective 80 Plus ratings.

Thermaltake shows us their third generation of Dr Power, the hardware-based in-line PSU tester. The new Dr Power III is aware of ATX 3.1, and has a native 12V-2x6 connector that's compatible with 12VHPWR. With this, you can check for faults in any of the voltage domains. The 24-pin connector should tell you if any of the smaller voltage domains such as 5 V, 5 Vsb, and 3.3 V, has suffered a fault.

NVIDIA today gave its GeForce RTX 40-series "Ada" a midlife refresh targeting the higher end of its product stack, with the new GeForce RTX 4070 SUPER, GeForce RTX 4070 Ti SUPER, and the GeForce RTX 4080 SUPER. The new RTX 4080 SUPER replaces the current RTX 4080, which will gradually be phased out of the market. The new RTX 4070 Ti SUPER does the same to the current RTX 4070 Ti. The RTX 4070 SUPER, however, will coexist with the current RTX 4070, albeit at a slight price premium. The RTX 4070 SUPER and RTX 4070 Ti SUPER are both being recommended by NVIDIA for maxed out 1440p gaming with full ray tracing; while the RTX 4080 SUPER is for those who want to max out gameplay at 4K with full ray tracing. The RTX 4070 SUPER and RTX 4070 Ti SUPER should still very much be capable of 4K gaming and more than acceptable frame rates, especially given the latest DLSS 3 Frame Generation and its proliferation among new AAA titles.

NVIDIA is giving the three new graphics card SKUs a staggered launch spread across January 2024. The RTX 4070 SUPER should be available to purchase on January 17, at a starting price of $599, which was the original MSRP of the RTX 4070. After this launch, the RTX 4070 slides down a bit to $549 while remaining in the product stack. Things get interesting higher up the stack. The RTX 4070 Ti SUPER, which goes on sale on January 24, is priced at $799, while the current RTX 4070 Ti is being retired from the product stack. The remaining RTX 4070 Ti cards should be up at slightly discounted prices.

Pictures of ZOTAC's custom-design GeForce RTX 4070 SUPER graphics cards hit the web. These look, unsurprisingly, similar to the company's custom-design RTX 4070 and RTX 4070 Ti graphics cards, reusing existing cooler designs, with the exception being the new SKU markings on the boxes. It's what's on the silicon that counts. ZOTAC's custom RTX 4070 SUPER lineup includes the TwinEdge and TwinEdge OC at price points close to NVIDIA's baseline price; and a premium SKU in the form of the Trinity Black. There may be more SKUs than the pictures leaked, given that there is an RTX 4070 AMP AIRO.

The TwinEdge is a compact board design that covers the basics. It is 2 slots thick, although about a half inch taller than what constitutes "full height." The cooler features a compact aluminium fin-stack heatsink, which is ventilated by a pair of fans. Unlike the RTX 4070 TwinEdge, the RTX 4070 SUPER TwinEdge could replace the single 8-pin PCIe power connector with a 12VHPWR, given that the TGP of the GPU is rumored to be 220 W. The Trinity Black is a more high-end looking product, with a triple-slot cooler, a roughly 31 cm card length, and 12 cm height, if the RTX 4070 Ti Trinity Black is anything to go by.

Seasonic is ready with a modular PSU cable for the new 12V-2x6 standard, which succeeds 12VHPWR. Intel felt the need to introduce the new cable standard as part of the new ATX 3.1 specification as the 12VHPWR is flimsy, and poses a burn-out hazard in case of an improper contact. For modular PSU manufacturers, implementing the new connector is as easy as selling or giving away a modular cable that plugs into the 12VHPWR connector on the PSU's backplane, and puts out a 12V-2x6 connector on the other end, and so as a leading power supply OEM, Seasonic is handing out such cables for free, but there's a catch.

Seasonic is giving away a modular PSU cable that plugs into a 12VHPWR on the PSU's backplate on one end, and puts out a new ATX 3.1 standards compliant 12V-2x6 connector on the other end, which promises greater mechanical stability over the 12VHPWR. The cable is free, however, it requires users to sign up to a "Beta Tester Program" by Seasonic. We haven't read the terms and conditions of the program, but we predict it to be a form of waiver against any damage liability—you use the cable at your own risk. The cable features 16-AWG wires, and a connector that's aligned at a 90° angle. The capable is capable of 600 W of continuous output and excursions within the ATX 3.1 and PCIe CEM 5.1 specifications.

Here are some of the first pictures of the ASUS GeForce RTX 4070 SUPER Dual OC, the company's close-to-MSRP custom-design implementation of the upcoming RTX 4070 SUPER, which is expected to be announced on January 8, with reviews and retail availability a week later. The card very closely resembles the design of the RTX 4070 Dual OC, but with one major difference—the single 8-pin PCIe power connector makes way for a 16-pin 12VHPWR. Considering that the ASUS Dual OC series tends to come with a nominal factory OC at power limits matching NVIDIA reference, this is the first sign that the RTX 4070 SUPER in general might have typical graphics power (TGP) above what a single 8-pin could fulfill, and so we've given a 12VHPWR, just like every RTX 4070 Ti. The cards will include an NVIDIA-designed adapter that converts two 8-pin PCIe to a 12VHPWR, with its signal pins set to tell the graphics card that it can deliver 300 W of continuous power.

The GeForce RTX 4070 SUPER is based on the same AD104 silicon as the RTX 4070 and RTX 4070 Ti, with its ASIC code rumored to be "AD104-350." The SKU allegedly enables 56 out of 60 streaming multiprocessors (SM) present on the silicon, giving it 7,168 out of 7,680 CUDA cores. This is a big increase from the 5,888 CUDA cores (46 SM) that the vanilla RTX 4070 is configured with. The memory subsystem is expected to be unchanged from the RTX 4070 and RTX 4070 Ti—12 GB of 21 Gbps GDDR6X across a 192-bit memory interface; leaving NVIDIA with one possible lever, the ROP count. While the RTX 4070 Ti has 80 ROPs, the RTX 4070 has 64. It remains to be seen how many the RTX 4070 SUPER gets. Its rumored TGP of 225 W is behind the switch to 12VHPWR connectors.